Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0705
(A) Any 2 or more of the following conditions are met simultaneously. (2 trip detection logic)
  1. One of the following conditions are met.
    P position signal is ON
    N position signal is ON
    Park/neutral position switch input signal is ON
  2. R position signal is ON
  3. D position signal is ON
  4. 2 position signal is ON
  5. L position signal is ON
  1. Wire harness or connector
  2. Shift lock control ECU (Transmission control switch)
  3. Park/neutral position switch
  4. ECM
(B) All of the following conditions are met simultaneously. (2 trip detection logic)
  1. P position signal is OFF
  2. N position signal is OFF
  3. Park/neutral position switch input signal is OFF
  4. R position signal is OFF
  5. D position signal is OFF
  6. 2 position signal is OFF
  7. L position signal is OFF
(C) When any of following conditions is met, the 3 position signal is ON for 2.0 seconds or more. (2 trip detection logic)
  1. P position signal is ON
  2. N position signal is ON
  3. Park/neutral position switch input signal is ON
  4. R position signal is ON
  5. 2 position signal is ON
  6. L position signal is ON

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
When the park/neutral position switch sends more than one signal at a time from switch positions P, R, N, D, 3, 2 or L, the ECM interprets this as a fault in the switch. The ECM turns on the MIL and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0705: Park/neutral position switch/Verify switch input
Required sensors/Components
Park/neutral position switch
Frequency of operation
Continuous
Duration
Condition (A) and (C):
2 seconds
Condition (B):
60 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present.
None
Ignition switch
ON
Battery voltage
10.5 V or more
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS

  1. One of the following conditions is met: Condition (A), (B) or (C)
  2. Condition (A)
    1. When 2 or more of the following signals are input at the same time

      One of the following conditions are met.
      P switch
      N switch
      Park/neutral position switch
      ON
      R switch
      ON
      D switch
      ON
      2 switch
      ON
      L switch
      ON
    Condition (B)
    1. All of following conditions are met

      P switch
      OFF
      N switch
      OFF
      Park/neutral position switch
      OFF
      R switch
      OFF
      D switch
      OFF
      2 switch
      OFF
      L switch
      OFF
    Condition (C)
    1. When any of following conditions is met, the 3 position signal is ON

      P switch
      ON
      N switch
      ON
      Park/neutral position switch
      ON
      R switch
      ON
      2 switch
      ON
      L switch
      ON

COMPONENT OPERATING RANGE


Park/neutral position switch
The park/neutral position switch sends only one signal to the ECM.

WIRING DIAGRAM


C233528E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in P and N
  2. ON: Shift lever in P or N
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in P
  2. ON: Shift lever in P
Shift SW Status (R Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in R
  2. ON: Shift lever in R
Shift SW Status (2 Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in 2
  2. ON: Shift lever in 2
Shift SW Status (L Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in L
  2. ON: Shift lever in L
Shift SW Status (N Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in N
  2. ON: Shift lever in N
Shift SW Status (D Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in D
  2. ON: Shift lever in D
Shift SW Status (3 Range)
PNP switch status/
OFF or ON
  1. OFF: Shift lever not in 3
  2. ON: Shift lever in 3
1.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH)


    C193930E17
  1. Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P1-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)


    C193930E11
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P1-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
Go to step 7
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH


    C224010E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever in P or N
    Below 1 Ω
    Shift lever not in P and N
    10 kΩ or higher
    2 (RB) - 6 (PL)
    Shift lever in P
    Below 1 Ω
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    Shift lever not in R
    10 kΩ or higher
    2 (RB) - 9 (NL)
    Shift lever in N
    Below 1 Ω
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever in D or 3
    Below 1 Ω
    Shift lever not in D and 3
    10 kΩ or higher
    2 (RB) - 3 (2L)
    Shift lever in 2
    Below 1 Ω
    Shift lever not in 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    Shift lever in L
    Below 1 Ω
    Shift lever not in L
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


4.INSPECT SHIFT LOCK CONTROL ECU (TRANSMISSION CONTROL SWITCH)


    C224012E01
  1. Connect the park/neutral position switch connector.

  1. Disconnect the shift lock control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (ATD) - 9 (NSSD)
    Shift lever in 3
    10 kΩ or higher
    Shift lever in D
    Below 1 Ω
    3 (AT3) - 9 (NSSD)
    Shift lever in 3
    Below 1 Ω
    Shift lever in D
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Lock Control ECU (Transmission Control Switch))



NG
REPLACE SHIFT LOCK CONTROL ECU (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)


    C224011E01
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S7-9 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever in D
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in D
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Shift Lock Control ECU (Transmission Control Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    C223986E02
  1. Connect the shift lock control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-23 (P) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in P
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in P
    Below 1 V
    E7-11 (R) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    E7-22 (N) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in N
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in N
    Below 1 V
    E7-21 (D) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in D
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in D
    Below 1 V
    E7-19 (3) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 3
    Below 1 V
    E7-10 (2) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in 2
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in 2
    Below 1 V
    E7-9 (L) - E4-3 (E1)
    1. Ignition switch ON
    2. Shift lever in L
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in L
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-30 (NSW) - P1-4 (B)
    Always
    Below 1 Ω
    P1-4 (B) - Body Ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)