DTC P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0756 | S2 stuck ON malfunction*1: The vehicle starts in 2nd gear and shifting to 4th gear is impossible. The ECM determines that there is a malfunction when both of the following conditions are met: (a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 2nd. (b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd. |
|
| P0756 | S2 stuck OFF malfunction*2: Shifting to 2nd and 3rd gears is impossible. The ECM determines that there is a malfunction when both of the following conditions are met: (a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 1st. (b) When the ECM directs the transmission to switch to 3rd gear, the actual gear is shifted to 4th. |
|
| Gear shift controlled by ECM | 1st | 2nd | 3rd | 4th |
| *1: Actual gear position under S2 stuck ON malfunction | 2nd | 2nd | 3rd | 3rd |
| *2: Actual gear position under S2 stuck OFF malfunction | 1st | 1st | 4th | 4th |
| Related DTCs | P0756: Shift solenoid valve S2/OFF malfunction Shift solenoid valve S2/ON malfunction |
| Required sensors/Components | Shift solenoid valve S2 |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0128 (ECT (Engine coolant temperature) sensor circuit) P0722 (Output speed sensor circuit) P0500 (Vehicle speed sensor circuit) |
| Transmission shift position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT (Engine Coolant Temperature) | 40°C (104°F) or more |
| Spark advance from max. retard timing by knock control | 0°CA or more |
| L4 switch | OFF |
| Transfer range | "HIGH" |
| Engine | Starting |
| ECM selected gear | 2nd |
| Vehicle speed | 10 km/h (6.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 3rd |
| Vehicle speed | Less than 10 km/h (6.2 mph) |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 10 km/h (6.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 1st |
| Vehicle speed | 10 km/h (6.2 mph) or more and Less than 40 km/h (24.8 mph) |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 3rd |
| Vehicle speed | 10 km/h (6.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 10 km/h (6.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at engine speed of 2000 rpm (Conditions vary with engine speed) |
| Input speed/Output speed (NC0/SP2) | 2.63 to 3.20 (This means actual gear is 1st) |
| Input speed/Output speed (NC0/SP2) | 0.00 to 0.22 (This means actual gear is 4th) |
| Input speed/Output speed (NC0/SP2) | 0.00 to 0.22 (This means actual gear is 4th) |
| Input speed/Output speed (NC0/SP2) | 1.40 to 1.67 (This means actual gear is 2nd) |
| Input speed/Output speed (NC0/SP2) | 0.93 to 1.07 (This means actual gear is 3rd) |
| Input speed/Output speed (NC0/SP2) | 0.93 to 1.07 (This means actual gear is 3rd) |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (30 mph) or less |
| ECM gear shift command | 1st | 2nd | 3rd | 4th |
| Shift solenoid valve S2 | OFF | ON | ON | OFF |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0756) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0756 is output | A |
| P0756 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE S2 |
![]() |
Remove shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
| Valve moves and makes an operating noise |
| *a | Component without harness connected (Shift Solenoid Valve S2) |
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||