DTC P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0751 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0751: Shift solenoid valve S1/OFF malfunction Shift solenoid valve S1/ON malfunction |
| Required sensors/Components (Main) | Shift solenoid valve S1 |
| Required sensors/Components (Related) | Vehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed sensor (NO) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) and (B): 0.4 seconds OFF malfunction (C): Immediate ON malfunction (A), (B) and (C): 0.4 seconds ON malfunction (D): 3 seconds ON malfunction (E): 0.5 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0128 (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) |
| ETCS (Electric throttle control system) | Not system down |
| Transmission range | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| Transfer range | "High" |
| ECM selected gear | 1st |
| Vehicle speed | 2 to 40 km/h (1.2 to 24.9 mph) |
| Throttle valve opening angle | 8% or more (When actual gear is 4th) 6.5% or more at 2000 rpm (Varies with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Continuous time for ECM selecting 4th gear | 2 seconds or more |
| Actual gear when ECM selected 4th gear | 4th |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| ECM selected gear | 1st |
| Vehicle speed | 2 to 40 km/h (1.2 to 24.9 mph) |
| Throttle valve opening angle | 8% or more (When actual gear is 4th) 6.5% or more at 2000 rpm (Varies with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Varies with engine speed) |
| ECM selected gear | 3rd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Varies with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) (After transition from 4th to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| Turbine speed/Output speed | 0.93 to 1.07 |
| Turbine speed/Output speed | 0.65 to 0.79 |
| Output record from ECM for 4th → 5th up-shift | Recorded |
| Turbine speed/Output speed | 3.30 to 7.50 |
| Turbine speed/Output speed | 1.91 to 2.35 |
| Turbine speed - Output speed x 4th gear ratio (NT - NO x 4th gear ratio) | 1000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1000 rpm or more |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, read the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (31 mph) or less |
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th |
| Shift solenoid valve S1 | ON | ON | OFF | OFF | OFF |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0751) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Turn the ignition switch off.
Lift the vehicle up.
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure when the engine is idling.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Follow the instructions on the Techstream and perform the Active Test.
Measure the line pressure with SST.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | OFF or ON
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE S1 |
![]() |
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Solenoid Connector (S1) - Solenoid Body (S1) | 20°C (68°F) | 11 to 15 Ω |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||