Home › TRANSMISSION · A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0751    Shift Solenoid "A" Performance (Shift Solenoid Valve S1)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd or 4th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body and automatic transmission (clutch, brake, gear, etc.).

DTC No.
DTC Detection Condition
Trouble Area
P0751
S1 stuck ON malfunction*1:
The ECM determines that there is a malfunction when both of the following conditions are met:
(a) When the ECM directs the transmission to switch to 4th gear, the engine overruns (clutch slips).
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 1st.
  1. Shift solenoid valve S1 is stuck open
  2. Valve body is blocked
  3. Shift solenoid valve S1
  4. Automatic transmission (clutch, brake, gear, etc.)
P0751
S1 stuck OFF malfunction*2:
The ECM determines that there is a malfunction when both of the following conditions are met:
(a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is also shifted to 4th.
  1. Shift solenoid valve S1 is stuck closed
  2. Valve body is blocked
  3. Shift solenoid valve S1
  4. Automatic transmission (clutch, brake, gear, etc.)

HINT:
Gear positions in the event of a solenoid valve mechanical problem:

Gear shift controlled by ECM
1st
2nd
3rd
4th
*1: Actual gear position under S1 stuck ON malfunction
1st
2nd
2nd
1st
*2: Actual gear position under S1 stuck OFF malfunction
4th
3rd
3rd
4th


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S1.
The ECM controls the gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0751:
Shift solenoid valve S1/OFF malfunction
Shift solenoid valve S1/ON malfunction
Required sensors/Components
Shift solenoid valve S1, Speed sensor (SP2), Speed sensor (NCO), Crankshaft position sensor (NE), Throttle position sensor, MAF
Frequency of operation
Continuous
Duration
OFF malfunction (A):
1 second
OFF malfunction (B):
0.4 seconds
ON malfunction (A):
0.8 seconds
ON malfunction (B):
Immediate
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0722 (Output speed sensor circuit)
P0500 (Vehicle speed sensor circuit)
Transmission shift position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT (Engine Coolant Temperature)
40°C (104°F) or more
Spark advance from max. retard timing by knock control
0°CA or more
L4 switch
OFF
Transfer range
"HIGH"
Engine
Starting

OFF malfunction (A) 
ECM selected gear
1st
Vehicle speed
10 km/h (6.2 mph) or more
and
Less than 40 km/h (24.8 mph)
Throttle valve opening angle
15% or more and
6.5% or more at engine speed of 2000 rpm
(Conditions vary with engine speed)

OFF malfunction (B) 
Current ECM selected gear
4th
Last ECM selected gear
3rd
Actual gear when ECM selected 3rd gear
3rd

ON malfunction (A) 
ECM selected gear
4th
Vehicle speed at current ECM selected gear
- Vehicle speed at last ECM selected gear
Less than 10 km/h (6.2 mph)
Throttle valve opening angle at current ECM selected gear
- Throttle valve opening angle at last ECM selected gear
Less than 10%
Throttle valve opening angle
Less than 20%
Vehicle speed
Less than 85 km/h (52.8 mph)
Engine speed
3200 rpm or more

ON malfunction (B) 
Current ECM selected gear
4th
Last ECM selected gear
3rd

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. Both of the following conditions are met: OFF malfunctions (A) and (B)
    2 detections are necessary in 1 driving cycle.
    1st detection: Temporary flag ON
    2nd detection: Pending fault code ON

OFF malfunctions (A) and (B) 
Input speed/Output speed (NC0/SP2)
0.00 to 0.22
(This means actual gear is 4th)
[ON malfunction]
  1. Both of the following conditions are met: ON malfunctions (A) and (B)

ON malfunction (A) 
NE current - NE last
NE current: Engine speed at current ECM selected gear
NE last: Engine speed at last ECM selected gear
950 rpm or more

ON malfunction (B) 
Input speed/Output speed (NC0/SP2)
Does not change as follows
0.93 to 1.07
(This means actual gear is 3rd)
↓
0.00 to 0.22
(This means actual gear is 4th)

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the Techstream, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    1. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (30 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
    2. The 3rd to 4th up-shift must be performed with the accelerator pedal released.
    3. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    4. The shift position commanded by the ECM is shown in the Data List display on the Techstream.
    5. Shift solenoid valve S1 turns ON/OFF normally when the shift lever is in D.

      ECM gear shift command
      1st
      2nd
      3rd
      4th
      Shift solenoid valve S1
      ON
      ON
      OFF
      OFF

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0751)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0751 is output
    A
    P0751 and other DTCs are output
    B

    HINT:
    If any other codes besides P0751 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT SHIFT SOLENOID VALVE S1


    C214962E01
  1. Remove shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S1 connector
    2. Battery negative (-) → Shift solenoid valve S1 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S1)


NG
REPLACE SHIFT SOLENOID VALVE S1 (Click here)
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)