Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0230 .

WIRING DIAGRAM


A193262E04


INSPECTION PROCEDURE

NOTICE:
Inspection the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FUEL PUMP OPERATION
  1. Check if there is pressure in the fuel inlet hose.

    HINT:
    If there is fuel pressure, you will hear the sound of fuel flowing.



NG
Go to step 5
OK


2.INSPECT FUEL PUMP RELAY
  1. Inspect the fuel pump relay (Click here).



NG
REPLACE FUEL PUMP RELAY
OK


3.INSPECT FUEL PUMP RESISTOR (RESISTANCE)
A193226E03
  1. Disconnect the fuel pump resistor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    0.70 to 0.76 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Fuel Pump Resistor)



NG
REPLACE FUEL PUMP RESISTOR
OK


4.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - FUEL PUMP RESISTOR - FUEL PUMP)
  1. Check the harness and connector between the fuel pump relay and fuel pump resistor.

    1. Remove the fuel pump relay from the engine room relay block.

    2. Disconnect the fuel pump resistor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      5 (Fuel pump relay holder) - F11-1
      Always
      Below 1 Ω
      5 (Fuel pump relay holder) or F11-1 - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and connector between the fuel pump resistor and fuel pump.

    1. Disconnect the fuel pump resistor connector.

    2. Disconnect the fuel pump connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      F11-2 - F19-4
      Always
      Below 1 Ω
      F11-2 or F19-4 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CIRCUIT OPENING RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Check whether operating sounds can be heard while operating the relay using the Techstream.

    OK:
    Operating sounds can be heard from relay.



NG
Go to step 11
OK


6.CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit.

    HINT:
    Refer to ECM Power Source Circuit (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FUEL PUMP RELAY
  1. Inspect the fuel pump relay (Click here).



NG
REPLACE FUEL PUMP RELAY
OK


8.INSPECT FUEL PUMP
A193234E02
  1. Inspect the fuel pump resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      4 (+) - 5 (-)
      20°C (68°F)
      0.2 to 3.0 Ω

Text in Illustration 
*a
Component without harness connected
(Fuel Pump)
  1. Inspect the fuel pump operation.

    1. Apply battery voltage to both terminals. Check that the pump operates.

      CAUTION:
      1. These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
      2. Keep the fuel pump as far away from the battery as possible.
      3. Always do the switching at the battery side.



NG
REPLACE FUEL PUMP (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP RELAY, FUEL PUMP - BODY GROUND)
  1. Check the harness and connector between the fuel pump and fuel pump relay.

    1. Disconnect the fuel pump connector.

    2. Remove the fuel pump relay from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      F19-4 - 4 (Fuel pump relay holder)
      Always
      Below 1 Ω
      F19-4 or 4 (Fuel pump relay holder) - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and connector between the fuel pump and body ground.

    1. Disconnect the fuel pump connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      F19-5 - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP RELAY)
  1. Remove the C/OPN relay from the engine room relay block.

  1. Remove the fuel pump relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3 (C/OPN relay holder) - 3 (Fuel pump relay holder)
    Always
    Below 1 Ω
    3 (C/OPN relay holder) or 3 (Fuel pump relay holder) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPAIR HARNESS OR CONNECTOR (EFI RELAY - CIRCUIT OPENING RELAY) 

11.INSPECT C/OPN RELAY
  1. Inspect the C/OPN relay (Click here).



NG
REPLACE C/OPN RELAY
OK


12.INSPECT ECM (FC VOLTAGE)
A193171E36
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-3 (FC) - E11-12 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
CHECK AND REPLACE HARNESS OR CONNECTOR (ECM - CIRCUIT OPENING RELAY - IGNITION SWITCH)
OK

REPLACE ECM (Click here)