Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.
If the ignition switch is turned off, the ECM holds the EFI relay ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve.

WIRING DIAGRAM


A193615E06


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT ECM (+B, +B2 VOLTAGE)
A193171E38
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-22 (+B) - E11-12 (E1)
    Ignition switch ON
    11 to 14 V
    E13-23 (+B2) - E11-12 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E11-12 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (IGSW VOLTAGE)
A193171E39
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E14-21 (IGSW) - E11-12 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 7
OK


4.INSPECT ECM (MREL VOLTAGE)
A193171E40
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-9 (MREL) - E11-12 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
REPLACE ECM (Click here)
OK


5.INSPECT EFI RELAY
  1. Inspect the EFI relay (Click here).



NG
REPLACE EFI RELAY
OK


6.CHECK HARNESS AND CONNECTOR (EFI RELAY- ECM, BODY GROUND)
  1. Remove the EFI relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1 (EFI relay holder) - E13-9 (MREL)
    Always
    Below 1 Ω
    3 (EFI relay holder) - E13-22 (+B)
    Always
    Below 1 Ω
    3 (EFI relay holder) - E13-23 (+B2)
    Always
    Below 1 Ω
    2 (EFI relay holder) - Body ground
    Always
    Below 1 Ω
    1 (EFI relay holder) or E13-9 (MREL) - Body ground
    Always
    10 kΩ or higher
    3 (EFI relay holder) or E13-22 (+B) - Body ground
    Always
    10 kΩ or higher
    3 (EFI relay holder) or E13-23 (+B2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - BATTERY) 

7.INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
  1. Disconnect the ignition switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I7-6 (IG2) - E14-21 (IGSW)
    Always
    Below 1 Ω
    I7-6 (IG2) or E14-21 (IGSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)