Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ACIS Control Circuit

for Preparation Click here


DESCRIPTION

This circuit opens and closes the intake air control valve in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
When the engine speed is between 2200 rpm and 4100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status), to close the intake air control valve. Under other conditions, the VSV is usually off and the intake air control valve is open.

A115903E05


WIRING DIAGRAM


A218146E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE VSV FOR ACIS)
A067588E18
  1. Disconnect the vacuum hose.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for AICS.

  1. Check the operation of the VSV when the VSV is operated by the Techstream.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

    Text in Illustration 
    *a
    VSV is ON
    *b
    VSV is OFF
    *c
    Air
    *d
    Port F
    *e
    Port E

Result 
Result
Proceed to
Outside standard range
A
Within standard range
B


B
Go to step 4
A


2.INSPECT VSV FOR ACIS
  1. Inspect the VSV for AICV (Click here).



NG
REPLACE VSV FOR ACIS
OK


3.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM, VSV FOR ACIS - EFI RELAY)
  1. Check the wire harness and connectors between the VSV for ACIS and ECM.

    1. Disconnect the VSV for ACIS connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      V3-2 (VSV for ACIS) - E11-19 (ACIS)
      Always
      Below 1 Ω
      V3-2 (VSV for ACIS) or E11-19 (ACIS) - Body ground
      Always
      10 kΩ or higher

  1. Check the wire harness between the VSV for ACIS and EFI relay.

    1. Disconnect the VSV for ACIS connector.

    2. Remove the EFI relay from the engine room R/B.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      V3-1 (VSV for ACIS) - 3 (EFI relay holder)
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK VACUUM HOSES (INTAKE MANIFOLD - INTAKE AIR CONTROL VALVE, INTAKE AIR CONTROL VALVE)
  1. Check that the vacuum hose is connected correctly.

  1. Check the vacuum hose for looseness and disconnection.

  1. Check the vacuum hose for cracks, holes and damage.



NG
REPAIR OR REPLACE VACUUM HOSES
OK


5.INSPECT INTAKE AIR CONTROL VALVE (INTAKE AIR SURGE TANK)
A075984E02
  1. Check that the lever moves when a vacuum of 26.6 kPa (200 mmHg) is applied with the vacuum gauge on.

    OK:
    Lever moves

  1. Check that the vacuum of 26.6 kPa (200 mmHg) is sustained for 1 minute in the above state.

    OK:
    Vacuum is sustained



NG
REPLACE INTAKE AIR CONTROL VALVE (INTAKE AIR SURGE TANK)
OK

REPLACE ECM (Click here)