Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > PRECAUTION

for Preparation Click here



1.TIRE PRESSURE WARNING SYSTEM PRECAUTION
  1. When the tire pressure warning light illuminates, immediately check the tire pressures and adjust them to the specified values. (The tire pressure warning light will illuminate after blinking for 1 minute if there is an open in the tire pressure warning light circuit.)

    Cold tire inflation pressure:

    Tire Size
    Front Pressure
    Rear Pressure
    P215/70R15
    210 kPa (2.1 kgf/cm2, 30 psi)
    230 kPa (2.3 kgf/cm2, 33 psi)
    P245/75R16
    210 kPa (2.1 kgf/cm2, 30 psi)
    210 kPa (2.1 kgf/cm2, 30 psi)
    P265/70R16
    200 kPa (2.0 kgf/cm2, 29 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)
    P265/65R17
    200 kPa (2.0 kgf/cm2, 29 psi)
    200 kPa (2.0 kgf/cm2, 29 psi)
    P255/45R18
    240 kPa (2.4 kgf/cm2, 35 psi)
    240 kPa (2.4 kgf/cm2, 35 psi)

  2. When the tire pressure warning light illuminates after blinking for 1 minute, there is a malfunction in the system. Check for DTCs.

  3. It is necessary to register the transmitter ID in the tire pressure warning ECU after replacing the tire pressure warning valve and transmitter and/or tire pressure warning ECU (Click here).

  4. When replacing the tire pressure warning ECU:

    1. Using the Data List, read the transmitter IDs registered in the ECU and make a note of them before removing the tire pressure warning ECU.

    2. Register the transmitter IDs after installing a new tire pressure warning ECU.



  5. When replacing the tire pressure warning valve and transmitter:



    1. Take a note of the 7 digit number (transmitter ID) written on the new tire pressure warning valve and transmitter when replacing the old one. Register the transmitter ID in the tire pressure warning ECU after replacing the tire pressure warning valve and transmitter and installing the tires and wheels on the vehicle.


      C191523E02


      Text in Illustration 
      *1
      Tire Pressure Warning Valve and Transmitter
      -
      -
      *a
      Transmitter ID (7 Digit Number)
      -
      -

      NOTICE:
      The transmitter ID is written on the tire pressure warning valve and transmitter. It will be unable to be read after installing the tire pressure warning valve and transmitter to the tire and wheel. Therefore, take a note of the transmitter ID before installing the tire pressure warning valve and transmitter.

  6. When replacing the tire pressure warning ECU and/or the tire pressure warning valves and transmitters:
    it is necessary to perform initialization (Click here) after the registration (Click here).

  7. Precautions about tire pressure:

    1. Tire pressure decreases naturally.
    2. In winter, tire pressure may decrease due to low ambient temperatures (tire pressure decreases by approximately 10 kPa (0.1 kgf/cm2, 1.45 psi) for every 10°C (18°F) drop in the ambient temperature). Therefore, the tire pressure warning is more likely to operate if the tire pressures are not adjusted appropriately. If the daily temperature variation is large, pressurize the tires high so that the tire pressures are suitable under cold conditions. As a result, incorrect tire pressure warning operation should decrease.


2.IN CASE OF TIRE AND WHEEL REPLACEMENT
  1. When tires and wheels are replaced, always ensure that each transmitter ID is correctly registered.


3.INITIALIZATION PRECAUTION
  1. Initialize the tire pressure warning system after any of the following is performed:

    1. Replacing the tire pressure warning ECU and/or a tire pressure warning valve and transmitter.
    2. Rotating tires on vehicles with differing front and rear tire inflation pressures.

    HINT:
    The tire pressure warning system will not operate properly if it is not initialized (Click here).


4.FAIL-SAFE FUNCTION
  1. When a system malfunction occurs in the tire pressure warning system, the tire pressure warning light illuminates after blinking for 1 minute and informs the driver of the system failure.

  2. The result of this diagnosis is stored in the tire pressure warning ECU.


5.CHECK TIRE PRESSURE AFTER REPAIRS
  1. After repairs, confirm that the actual tire pressures are displayed in the Data List (Click here).