DTC P0781 1-2 Shift (1-2 Shift Valve) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0781 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0781: Valve body/Rationality check |
| Required sensors/Components (Main) | Valve body |
| Required sensors/Components (Related) | Automatic transmission assembly, Speed sensor (NT), Speed sensor (NO), Vehicle speed sensor, Throttle position sensor |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (B): 0.4 seconds Condition (C): 3 seconds Condition (D): 0.5 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0128 (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) |
| ETCS (Electric throttle control system) | Not system down |
| Transmission range | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| Transfer range | "High" |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Varies with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Varies with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) (After transition from 4th to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| Turbine speed/Output speed | 3.30 to 7.50 |
| Turbine speed/Output speed | 1.28 to 1.53 |
| Turbine speed - Output speed x 4th gear ratio (NT - NO x 4th gear ratio) | 1000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1000 rpm or more |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0781 is output | A |
| P0781 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST) |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test using the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (31 mph) or less |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Turn the ignition switch off.
Lift the vehicle up.
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure when the engine is idling.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Follow the instructions on the Techstream and perform the Active Test.
Measure the line pressure with SST.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | OFF or ON
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 4.CLEAR DTC |
Clear DTC (Click here).
| NEXT | |
| 5.PERFORM MONITOR DRIVING PATTERN |
Perform Monitor Drive Pattern for ECT test (Click here).
| NEXT | |
| 6.CHECK DTC OUTPUT (P0781) |
Check DTC output (Click here).
| Result | Proceed to |
| DTC P0781 is not output | A |
| DTC P0781 is output | B |
|
| ||||
| A | ||
| ||