Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor assembly and the seat position sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position sensor assembly circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor assembly circuit for 2 seconds.
  2. Seat position sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. No. 1 seat wire*1
  3. Front seat belt inner assembly LH*2
  4. Seat position sensor
  5. Center airbag sensor assembly
*1: for Bench Seat Type
*2: for Separate Seat Type

WIRING DIAGRAM


C190118E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch off.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat outer belt assembly LH.
  7. (g) Disconnect the connector from the front seat outer belt assembly RH.
  8. (h) Disconnect the connector from the front seat airbag assembly LH.
  9. (i) Disconnect the connector from the front seat airbag assembly RH.
  10. (j) Disconnect the connector from the curtain shield airbag assembly LH.
  11. (k) Disconnect the connector from the curtain shield airbag assembly RH.
1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


2.CHECK CONNECTORS
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Disconnect the connector from the seat position sensor.

  1. Check that the connectors (on the center airbag sensor assembly side and seat position sensor side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.

    Condition
    Proceed to
    Normal (separate seat)
    A
    Normal (bench seat)
    B
    Abnormal
    C



B
Go to step 5

C
REPLACE HARNESS OR CONNECTOR
A


3.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

C172903E03

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F20-3 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    F20-4 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F20-3 (LSP+) - F20-4 (LSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F20-3 (LSP+) - F20-4 (LSP-)
    Always
    1 MΩ or Higher
    F20-3 (LSP+) - Body ground
    Always
    1 MΩ or Higher
    F20-4 (LSP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK SEAT POSITION SENSOR


    C190119E01
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the seat position sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK SEAT POSITION SENSOR CIRCUIT (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

C162324E04

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S25-2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    S25-1 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S25-2 (LSP+) - S25-1 (LSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S25-2 (LSP+) - S25-1 (LSP-)
    Always
    1 MΩ or Higher
    S25-2 (LSP+) - Body ground
    Always
    1 MΩ or Higher
    S25-1 (LSP-) - Body ground
    Always
    1 MΩ or Higher



NG
Go to step 7
OK


6.CHECK SEAT POSITION SENSOR


    H100890E09
  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the seat position sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

C162326E02

  1. Disconnect the No. 2 floor wire connector from the No. 1 seat wire.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    BK1-3 (DSP+) - Body ground
    Ignition switch ON
    Below 1 V
    BK1-4 (DSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-3 (DSP+) - BK1-4 (DSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    BK1-3 (DSP+) - BK1-4 (DSP-)
    Always
    1 MΩ or Higher
    BK1-3 (DSP+) - Body ground
    Always
    1 MΩ or Higher
    BK1-4 (DSP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE NO. 1 SEAT WIRE 

8.REPLACE SEAT POSITION SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the seat position sensor for Bench Seat Type (Click here) or for Separate Seat Type (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY
C190120E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

HINT:
DTCs other than B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

END