Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E232743E02


INSPECTION PROCEDURE

NOTICE:
  1. The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio and display receiver assembly, steering pad switch, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the TAIL or HEAD position.
    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except radio and display receiver assembly.
    B
    Illumination comes on for all components except steering pad switch assembly and radio and display receiver assembly.
    C



B
Go to step 6

C
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)


    E232744E01
  1. Disconnect the S8 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S8-12 (IL+2) - Body ground
    Light control switch in the tail or head position
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the z1 steering pad switch assembly connector.



  1. Disconnect the S8 spiral cable sub-assembly connector.


    E233335E01


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    -
    -

  1. Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    E170601E13
  1. Disconnect the z1 steering pad switch assembly connector.

  1. Disconnect the S8 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z1-8 (EAU) - S8-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    Below 1 Ω
    2.5 rotations to the right
    Below 1 Ω
    z1-5 (IL+2) - S8-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    Below 1 Ω
    2.5 rotations to the right
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side

    NOTICE:
    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
  1. Disconnect the R15 radio and display receiver assembly connector.

  1. Disconnect the S8 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R15-23 (SWG) - S8-4 (EAU)
    Always
    Below 1 Ω
    R15-23 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)


    E233350E01
  1. Disconnect the R16 radio and display receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R16-2 (ILL+) - Body ground
    Light control switch in the tail or head position
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - LIGHT CONTROL RHEOSTAT)
  1. Disconnect the R16 radio and display receiver assembly connector.

  1. Disconnect the R4 light control rheostat connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R16-12 (ILL-) - R4-6 (ILL-)
    Always
    Below 1 Ω
    R16-12 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)