Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM


E232741E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)


    E232742E01
  1. Disconnect the R3 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R3-7 (SW1) - R3-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    R3-8 (SW2) - R3-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    MODE switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    Voice switch pushed
    2955 to 3265 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver Assembly)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the z1 steering pad switch assembly connector.


    E233334E01


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    Seek+
    *e
    Seek-
    *f
    MODE
    *g
    On hook
    *h
    Off hook
    *i
    Voice
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    z1-10 (AU1) - z1-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    z1-9 (AU2) - z1-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    Voice switch pushed
    2955 to 3265 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    E170601E12
  1. Disconnect the z1 steering pad switch assembly connector.

  1. Disconnect the S8 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z1-8 (EAU) - S8-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    Below 1 Ω
    2.5 rotations to the right
    Below 1 Ω
    z1-10 (AU1) - S8-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    Below 1 Ω
    2.5 rotations to the right
    Below 1 Ω
    z1-9 (AU2) - S8-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    Below 1 Ω
    2.5 rotations to the right
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Steering Pad Switch Assembly Side
    *c
    Vehicle Side

    NOTICE:
    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)