Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes by the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No.
DTC Detection Condition
Trouble Area
P0340
Either of following conditions is met:
  1. No camshaft position sensor signal to ECM while cranking (2 trip detection logic)
  2. No camshaft position sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Camshaft
  4. Jumped tooth of timing chain
  5. ECM

HINT:
DTC P0340 indicates a malfunction relating to the camshaft position sensor (+) circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).

Reference: Inspection using an oscilloscope
A063955E51

HINT:
  1. The correct waveform is as shown above.
  2. G2 stands for the camshaft position sensor signal, and NE+ stands for the crankshaft position sensor signal.
    ECM Terminal Name
    (a) Between G2 and NE-
    (b) Between NE+ and NE-
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling


MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the engine revolving, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0340: Camshaft Position Sensor Verify Pulse Input
P0340: Camshaft Position/Crankshaft Position Misalignment
Required Sensors/Components (Main)
Camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
4 seconds: P0340 (verify pulse input)
5 seconds: P0340 (misalignment)
MIL Operation
2 driving cycles: Camshaft position sensor verify pulse input
Immediate: Camshaft position/crankshaft position misalignment
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

Camshaft Position Sensor Verify Pulse Input P0340: 
Starter
ON
Minimal battery voltage while starter ON
Less than 11 V

Camshaft Position/Crankshaft Position Misalignment P0340: 
Engine speed
600 rpm or more
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Camshaft Position Sensor Verify Pulse Input P0340: 
Camshaft position sensor signal
No signal

Camshaft Position/Crankshaft Position Misalignment P0340: 
Camshaft position and crankshaft position phase
Misaligned

COMPONENT OPERATING RANGE


Camshaft position sensor
  1. Camshaft position sensor output voltage fluctuates while camshaft revolving
  2. 3 camshaft position sensor signals per 2 crankshaft revolutions

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read the DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
G037727E21
  1. Disconnect the C1 camshaft position sensor connector.

  1. Measure the resistance between terminals 1 and 2.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
835 to 1400 Ω
1 - 2
Hot
1060 to 1645 Ω

HINT:
Terms cold and hot refer to the temperature of the coils. Cold means approximately -10 to 50°C (14 to 122°F). Hot means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CAMSHAFT POSITION SENSOR (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
A113507E03
  1. Disconnect the C1 camshaft position sensor connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C1-1 (G+) - E4-26 (G2)
    Always
    Below 1 Ω
    C1-2 (G-) - E4-34 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C1-1 (G+) or E4-26 (G2) - Body ground
    Always
    10 kΩ or higher
    C1-2 (G-) or E4-34 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
BR03795E22
  1. Check the camshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
OK

REPLACE ECM (Click here)