Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0112    Intake Air Temperature Circuit Low Input

DTC    P0113    Intake Air Temperature Circuit High Input

for Preparation Click here


DESCRIPTION


  1. A056276E16
  2. The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature sensor is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
    The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
    Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies.
    Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.

HINT:
When any of DTCs P0112 and P0113 are stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
DTC Detection Condition
Trouble Area
P0112
Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter sub-assembly)
  3. ECM
P0113
Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter sub-assembly)
  3. ECM

HINT:
When any of these DTCs are output, check the intake air temperature sensor by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
Higher than 128°C (262°F)
Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature.
When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and stored the DTC.
Example:
If the sensor voltage output is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the voltage output is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stored DTC P0112.
If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0112: Intake air temperature sensor short (Low electrical resistance)
P0113: Intake air temperature sensor open (High electrical resistance)
Required Sensors/Components (Main)
Intake air temperature sensor
Required sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


P0112 
Intake air temperature sensor voltage
Less than 0.18 V [Higher than 128°C (262°F)]

P0113 
Intake air temperature sensor voltage
More than 4.91 V [Less than -55°C (-67°F)]

COMPONENT OPERATING RANGE


Intake air temperature sensor voltage
0.18 to 4.91 V [-55 to 128°C (-67 to 262°F)]

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 0.5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0112 or P0113.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A193263E07


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    Same as actual intake air temperature.


    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    Higher than 128°C (262°F)
    B
    Same as actual intake air temperature
    C

    HINT:
    1. If there is an open circuit, the Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, the Techstream indicates higher than 128°C (262°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
A116161E09
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter sub-assembly wire harness side connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard value:
    Higher than 128°C (262°F)

    Text in Illustration 
    *1
    Mass Air Flow Meter Sub-assembly
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter Sub-assembly)



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

3.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN ECM)
A218164E04
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Connect terminals THA and ETHA of the ECM connector.

    HINT:
    Before checking, do visual and contact pressure checks on the ECM connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard value:
    Higher than 128°C (262°F)

    Text in Illustration 
    *1
    Mass Air Flow Meter Sub-assembly
    *2
    ECM
    *a
    Component with harness connected
    (ECM)



NG
CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) 

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
A186168E05
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard value:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Mass Air Flow Meter Sub-assembly
    *2
    ECM



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

5.READ VALUE USING TECHSTREAM (CHECK FOR SHORT ECM)
A193185E03
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard value:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Mass Air Flow Meter Sub-assembly
    *2
    ECM
    *a
    Rear view of wire harness connector
    (to ECM)



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)