Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

DTC    C1380    Stop Light Control Relay Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU (master cylinder solenoid) inputs the stop light switch signal and detects the status of the brake operation.

DTC Code
DTC Detection Condition
Trouble Area
C1380
Either condition is met:
  1. When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light driving output (STPO) is on, and a signal has not been input to the STP terminal for 5 seconds or more.
  2. When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light driving output (STPO) is off, and the input signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.
  1. STOP fuse
  2. Harness or connector
  3. Stop light control relay (STOP LP CTRL)
  4. Skid control ECU (master cylinder solenoid)

WIRING DIAGRAM


C248750E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).

1.CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Stop light switch function is normal.



NG
Go to step 10
OK


2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C213546E19
  1. Disconnect the skid control ECU (master cylinder solenoid) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    S1-7 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)


    C213546E22
  1. Disconnect the skid control ECU (master cylinder solenoid) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S1-45 (STP2 )- Body ground
    Brake pedal depressed
    8 to 14 V
    S1-45 (STP2 )- Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT RELAY)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control relay (STP LP CTRL)
    OFF/ON
    Observe the stop lights (does not come on for 2 to 5 seconds).

  1. Check that the stop lights turn on and off on the rear combination light when using the Techstream.

OK:
The stop lights turn on and off according to the Techstream operations.



NG
Go to step 6
OK


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

6.CHECK HARNESS AND CONNECTOR (STOP LP CTRL RELAY TERMINAL)


    F101151E01
  1. Remove the STOP LP CTRL relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Ignition switch ON
    8 to 14 V
    5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    STOP LP CTRL Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LP CTRL RELAY CIRCUIT)
OK


7.INSPECT STOP LP CTRL RELAY


    E149024E04
  1. Remove the STOP LP CTRL relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage not applied
    Below 1 Ω
    Battery voltage applied to terminal 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    STOP LP CTRL Relay



NG
REPLACE STOP LP CTRL RELAY
OK


8.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)


    C213546E20
  1. Disconnect the skid control ECU (master cylinder solenoid) connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S1-16 (STPO) - Body ground
Ignition switch ON
11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)
OK


9.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

10.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
  1. Disconnect the stop light switch assembly connector.



    C204290E06
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S10-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


11.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Disconnect the stop light switch assembly connector.



    C124796E18
  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Switch Connection
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (to Stop Light Switch Assembly)
    *1
    Pushed in
    *2
    Free

  1. Reconnect the stop light switch assembly connector.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LP CTRL RELAY)
  1. Remove the STOP LP CTRL relay from the engine room relay block.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S10-1 - STOP LP CTRL relay-4
    Always
    Below 1 Ω
    S10-1 - Body ground
    Always
    10 Ω or higher

  1. Reinstall the STOP LP CTRL relay from the engine room relay block.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT STOP LP CTRL RELAY
  1. Remove the STOP LP CTRL relay from the engine room relay block.



    E149024E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage not applied
    Below 1 Ω
    Battery voltage applied to terminal 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminal 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    STOP LP CTRL Relay



NG
REPLACE STOP LP CTRL RELAY
OK


14.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY, HIGH MOUNTED STOP LIGHT ASSEMBLY - STOP LP CTRL RELAY)
  1. Disconnect the rear combination light assembly connector.

  1. Disconnect the high mounted stop light assembly connector.

  1. Remove the STOP LP CTRL relay.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Rear Combination Light Assembly RH 
    Tester Connection
    Condition
    Specified Condition
    R6-4 - STOP LP CTRL-3
    Always
    Below 1 Ω
    R6-4 - Body ground
    Always
    10 kΩ or higher
    R6-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    Rear Combination Light Assembly LH 
    Tester Connection
    Condition
    Specified Condition
    R5-4 - STOP LP CTRL-3
    Always
    Below 1 Ω
    R5-4 - Body ground
    Always
    10 kΩ or higher
    R5-3 - Body ground
    Always
    Below 1 Ω

    Standard Resistance:
    High Mounted Stop Light Assembly 
    Tester Connection
    Condition
    Specified Condition
    C15-1 - STOP LP CTRL-3
    Always
    Below 1 Ω
    C15-1 - Body ground
    Always
    10 kΩ or higher
    C15-2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the STOP LP CTRL relay.

  1. Reconnect the rear combination light assembly connector.

  1. Reconnect the high mounted stop light assembly connector.
    Result 
    Result
    Proceed to
    NG
    A
    OK (Rear Combination Light Assembly)
    B
    OK (High Mounted Stop Light Assembly)
    C



B
Go to step 15

C
Go to step 16
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

15.INSPECT REAR COMBINATION LIGHT ASSEMBLY
  1. Remove the rear combination light assembly connector .



    C248754E01
  1. Apply battery voltage to the terminals and check that the rear combination light illuminates.
    OK 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 4
    Negative battery - Terminal 3
    Rear combination light illuminates
    Text in Illustration 
    *a
    Component without harness connected
    (to Rear Combination Light Sssembly)

  1. Reinstall the rear combination light assembly.



NG
REPLACE REAR COMBINATION LIGHT ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK (Click here)  

16.INSPECT CENTER STOP LIGHT BULB
  1. Remove the high mounted stop light assembly connector.



    C248753E01
  1. Apply battery voltage to the terminals and check that the rear combination light illuminates.
    OK 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 1
    Negative battery - Terminal 2
    High mounted stop light illuminates
    Text in Illustration 
    *a
    Component without harness connected
    (to High Mounted Stop Light Assembly)

  1. Reinstall the high mounted stop light assembly.



NG
REPLACE CENTER STOP LIGHT BULB
OK

USE SIMULATION METHOD TO CHECK (Click here)