Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0722    Output Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The speed sensor (SP2) detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor (SP2) coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor. The gear shift point and lock-up timing are controlled by the ECM based on the signals from the vehicle speed sensor and the throttle position sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0722
  1. All conditions below are detected 5 seconds or more continuously (2-trip detection logic)
    1. No signal from speed sensor (SP2) is input to ECM while 4 pulses of No. 1 vehicle speed sensor signal are sent.
    2. Vehicle speed is 9 km/h (5.6 mph) or more
  1. Open or short in speed sensor (SP2) circuit
  2. Speed sensor (SP2)
  3. ECM
Using an oscilloscope:
Check the waveform between terminals SP2+ and SP2- of the ECM connector.
C189668E01

Standard:
Refer to the illustration.

Terminal
SP2+ - SP2-
Tool setting
2 V/DIV, 20 msec./DIV
Vehicle condition
Vehicle speed 20 km/h (12 mph)

MONITOR DESCRIPTION

The output speed sensor monitors the output shaft speed. The ECM controls the gearshift point and the lock up timing based on the signals from the output speed sensor and throttle position sensor.
If the ECM detects no signal from the output shaft speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the output speed sensor. The ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY


Related DTCs
P0722 : speed sensor (SP2)/Verify pulse input
Required Sensors/Components
Speed sensor (SP2)
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
None
Vehicle speed at vehicle speed sensor
9 km/h (5.6 mph) or more

TYPICAL MALFUNCTION THRESHOLDS


Output speed sensor pulse signal
No signal

COMPONENT OPERATING RANGE


Vehicle speed at output speed sensor
9 km/h (5.6 mph) or more

WIRING DIAGRAM


C186140E03


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    0 km/h (0 mph) (output shaft speed is equal to vehicle speed): Vehicle stopped
    -

    HINT:
    1. SPD (SP2) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. The SPD (SP2) value displayed on the Techstream is much lower than the actual vehicle speed:
      Sensor trouble, improper installation, or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR (SP2) INSTALLATION


    C159067E06
  1. Check the speed sensor (SP2) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (SP2)
OK


2.INSPECT SPEED SENSOR (SP2)


    E116970E31
  1. Disconnect the speed sensor (SP2) connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (SP2) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (SP2) - ECM)


    C189655E02
  1. Connect the speed sensor (SP2) connector.

  1. Disconnect the connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-9 (SP2+) - E11-10 (SP2-)
    20°C (68°F)
    560 to 680 Ω
    E11-9 (SP2+) - Body ground
    Always
    10 kΩ or higher
    E11-10 (SP2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)