Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING ECU

TIRE PRESSURE WARNING ECU > INSTALLATION

for Preparation Click here



1. INSTALL TIRE PRESSURE WARNING ECU


C189607
  1. Install the tire pressure warning ECU with the 2 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



2. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



3. INSTALL LOWER INSTRUMENT PANEL LH
  1. Install the lower instrument panel LH with the 3 bolts <B>.



4. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



5. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B290404
  1. Pull the bottom of the stopper.



    B290405
  1. Attach the stopper to the glove compartment door as shown in the illustration.



    E232355
  1. Install the glove compartment door assembly with 3 hinges, holding it horizontal.



    E232356
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.



6. INSTALL INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



7. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



8. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



9. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



10. INSTALL RADIO RECEIVER ASSEMBLY
  1. Connect all the connectors.

  1. Connect the plug.

  1. Engage the 5 clips and install the radio receiver assembly with bracket.

  1. Install the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



11. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    E212050
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



12. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B290406
  1. Install the 2 instrument panel cup holders.

  1. Install the box bottom mat.

  1. Install the shift knob.



13. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B290407
  1. Install the 2 instrument panel cup holders.

  1. Install the box bottom mat.

  1. Install the shift knob.



14. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    E232357
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



15. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.



16. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.

  1. Install the 2 instrument panel cup holders.



17. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B290408
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.

  1. Install the console box carpet.



18. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)
  1. Engage the 4 clips and claw, and install the console upper panel sub-assembly.



19. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B290409
  1. Engage the 6 clips and claw, and install the console upper rear panel.

  1. Install the shift knob.



20. INSTALL INSTRUMENT PANEL HOLE COVER (for Manual Transmission)
  1. Engage the 4 clips and install the instrument panel hole cover.



21. INSTALL INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission)
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



22. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



23. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



24. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



25. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)
  1. Install the front door opening trim weatherstrip.



26. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab)
  1. Engage the 9 claws and clip, and install the front door scuff plate.



27. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab)
  1. Engage the 9 claws and install the front door scuff plate.



28. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

(Click here)


30. REGISTER TRANSMITTER ID
  1. Register the transmitter ID (Click here).



31. PERFORM INITIALIZATION (for Tire Pressure Warning System)
  1. When the ECU is replaced, perform initialization (Click here).