Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (w/o Navigation System)

REAR VIEW MONITOR SYSTEM (w/o Navigation System) > Reverse Signal Circuit


DESCRIPTION

The inner rear view mirror assembly receives a reverse signal from the park/neutral position switch assembly*1 or the back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM


E236285E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT INNER REAR VIEW MIRROR ASSEMBLY (REVERSE SIGNAL)


    E236286E01
  1. Disconnect the I8 inner rear view mirror assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I8-3 (REV) - Body ground
    Ignition switch ON,
    shift lever in not R
    Below 1 V
    Ignition switch ON,
    shift lever in R
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inner Rear View Mirror Assembly)

  1. Reconnect the inner rear view mirror assembly connector.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    for Automatic Transmission
    A
    for Manual Transmission
    B



B
Go to step 5
A


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (IG SIGNAL)


    E236287E01
  1. Disconnect the P1 park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P1-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)

  1. Reconnect the park/neutral position switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the I8 inner rear view mirror assembly connector.

  1. Disconnect the P1 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I8-3 (REV) - P1-1 (RL)
    Always
    Below 1 Ω
    I8-3 (REV) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for A340E)
    B
    OK (for A750E)
    C
    OK (for A750F)
    D

  1. Reconnect the inner rear view mirror assembly connector.

  1. Reconnect the park/neutral position switch assembly connector.



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

D
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY (IG SIGNAL)


    E168289E04
  1. Disconnect the B1 back-up light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-2 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the back-up light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the I8 inner rear view mirror assembly connector.

  1. Disconnect the B1 back-up light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I8-3 (REV) - B1-1 (RL)
    Always
    Below 1 Ω
    I8-3 (REV) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for R155)
    B
    OK (for R155F)
    C
    OK (for RA60)
    D
    OK (for RA60F)
    E

  1. Reconnect the inner rear view mirror assembly connector.

  1. Reconnect the back-up light switch assembly connector.



B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

C
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

D
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

E
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR