Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P060E    Internal Control Module Throttle Position Performance

for Preparation Click here


DESCRIPTION

The ECM monitors the input signals of the throttle position sensor No. 1 and stop light switch assembly. As the ECM monitors the input signals of the throttle position sensor No. 1 and the STP signals of the stop light switch assembly, if the input signals and control signals are deviated, a DTC is stored.

DTC No.
DTC Detection Condition
Trouble Area
P060E
When either condition below is met (1 trip detection logic):
  1. ECM main CPU error
  2. ECM sub CPU error
ECM

MONITOR STRATEGY


Related DTCs
P060E: Internal Control Module, Throttle Position
Required sensors / components (Main)
ECM
Required sensors / components (Related)
-
Frequency of operation
Once per driving cycle
Duration
1 second: Case 1
13 times: Case 2
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Case 1 
Monitor runs whenever following DTCs not stored
None

Case 2 
Monitor runs whenever following DTCs not stored
None
DMA communication error
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
Difference of main throttle position and sub throttle position
0.3 V or more

Case 2 
Difference of main brake switch signal and sub brake switch signal
Different

CONFIRMATION DRIVING PATTERN

NOTICE:
After turning ignition switch off, waiting may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the Techstream off.
  5. Turn the ignition switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the Techstream to the DLC3.
  10. Turn the ignition switch to ON and turn the Techstream on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  13. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P060E.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

NOTICE:
After turning ignition switch off, waiting may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC (DTC P060E)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTC (Click here).

  1. Turn the ignition switch off and turn the Techstream off.

  1. Disconnect the Techstream.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT/ Trouble Codes.

  1. Read DTCs.

    OK:
    DTC P060E is not output.



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)