DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0011 P0021 | Valve timing is not adjusted in valve timing advance range (1 trip detection logic) |
|
| P0012 P0022 | Valve timing is not adjusted in valve timing retard range (2 trip detection logic) |
| Related DTCs | P0011: Advanced camshaft timing (bank 1) P0012: Retarded camshaft timing (bank 1) P0021: Advanced camshaft timing (bank 2) P0022: Retarded camshaft timing (bank 2) |
| Required Sensors/Components (Main) | VVT OCV and VVT Actuator |
| Required Sensors/Components (Related) | Crankshaft position sensor, VVT sensor and Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Within 10 seconds |
| MIL Operation | Advanced camshaft timing: Immediate Retarded camshaft timing: 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil Control Valve) P0016, P0018 (VVT System - Misalignment) P0102, P0103 (Mass Air Flow Meter) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) |
| Battery voltage | 11 V or more |
| Engine RPM | 500 to 4000 rpm |
| ECT | 75 to 100°C (167 to 212°F) |
| All of following conditions are met | - |
| Deactivation of actual valve timing and target valve timing | More than 5°CA (crankshaft angle) |
| Valve timing | No change at advanced (retarded) valve timing |
| Abnormal bank | Advanced timing over (Valve timing is out of specified range) | Retarded timing over (Valve timing is out of specified range) |
| Bank 1 | P0011 | P0012 |
| Bank 2 | P0021 | P0022 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0011, P0012, P0021 or P0022 | A |
| P0011, P0012, P0021 or P0022 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream ON.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the Techstream ON.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the Techstream (Click here).
Drive the vehicle for more than 10 minutes.
Read DTCs using the Techstream.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN) |
![]() |
Remove the cylinder head cover .
Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
Reinstall the cylinder head cover .
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Remove the OCV (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
Remove oil control valve filter .
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
Replace camshaft timing gear assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the Techstream ON.
Clear DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the Techstream (Click here).
Drive the vehicle for more than 10 minutes.
Read output DTCs using the Techstream.
|
| ||||
| OK | ||
| ||