Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC Code
DTC Detection Condition
Trouble Area
P0116
When either of following conditions met (2 trip detection logic):
  1. When cold engine started and engine warmed up, Engine Coolant Temperature (ECT) sensor value does not change.
  2. After warmed up engine stopped and then next cold engine start performed, ECT sensor value does not change.
  1. Thermostat
  2. ECT sensor
P0116
For Mexico Models:
Case 1:
Engine Coolant Temperature (ECT) between 35°C and 60°C (95°F and 140°F) when engine started, and conditions (a) and (b) met (2 trip detection logic)
(a) Vehicle driven at varying speeds (accelerated and decelerated)
(b) ECT remains within 3°C (5.4°F) of initial ECT
Case 2:
ECT more than 60°C (140°F) when engine started, and conditions (a) and (b) met (6 trip detection logic) (a) Vehicle driven at varying speeds (accelerated and decelerated)
(b) ECT measurements remain within 1°C (1.8°F) of initial ECT on 6 successive occasions
  1. Thermostat
  2. ECT sensor

MONITOR DESCRIPTION

  1. Engine coolant temperature (ECT) sensor cold start monitor
    When a cold engine start is performed and then the engine is warmed up, if the ECT sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is set.
  1. ECT sensor soak monitor
    If the ECT sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is set.
  1. ECT sensor high side stuck monitor (only for Mexico models)
    The ECM monitors the sensor voltage and uses this value to calculate the ECT. If the sensor voltage output deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the ECT sensor and sets the DTC.
    Examples:
    1. Upon starting the engine, the ECT is between 35°C and 60°C (95°F and 140°F). If after driving for 250 seconds, the ECT remains within 3°C (5.4°F) of the starting temperature, the DTC is set (2 trip detection logic).
    2. Upon starting the engine, the ECT is over 60°C (140°F). If after driving for 250 seconds, the ECM remains within 1°C (1.8°F) of the starting temperature, the DTC is set (6 trip detection logic).

MONITOR STRATEGY


Related DTCs
P0116: Engine coolant temperature (ECT) sensor cold start monitor
P0116: ECT sensor soak monitor
Required Sensors/Components (Main)
ECT sensor
Required Sensors/Components (Related)
None
Frequency of Operation
Once per driving cycle
Duration
5 hours or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


ECT sensor cold start monitor: 
Monitor runs whenever following DTCs not present
P0110, P0112, P0113 (Intake Air Temperature Sensor)
Battery voltage
10.5 V or more
Time after engine start
1 second or more
ECT at engine start
Less than 60°C (140°F)
Soak time
0 or more
Accumulated MAF
1670 g or more
Engine
Running
Fuel cut
OFF
Difference between ECT at engine start and IAT
Less than 40°C (72°F)

ECT sensor soak monitor: 
Monitor runs whenever following DTCs not present
P0110, P0112, P0113 (Intake Air Temperature Sensor)
Battery voltage
10.5 V or more
Engine
Running
Soak time
5 hours or more
Either (a) or (b) condition met
-
(a) ECT
60°C (140°F) or more
(b) Accumulated MAF
3295 g or more

TYPICAL MALFUNCTION THRESHOLDS


ECT sensor cold start monitor: 
ECT sensor value change
Less than 5°C (9°F)

ECT sensor soak monitor: 
Difference between current ECT sensor value and previous ECT sensor value when engine stopped
Less than 5°C (9°F)

COMPONENT OPERATING RANGE


ECT
ECT sensor value changes in accordance with actual ECT

INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0117, P0118 or P0125 are set simultaneously with DTC P0116, the ECT sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTC.


Result:

Display (DTC Output)
Proceed to
P0116
A
P0116 and other DTCs
B



B
GO TO DTC CHART (Click here)
A


2.INSPECT WATER INLET WITH THERMOSTAT
  1. Remove the water inlet with thermostat (Click here).

  1. Measure the valve opening temperature of the thermostat.

    Standard value:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the water inlet with thermostat (Click here).



NG
REPLACE WATER INLET WITH THERMOSTAT (Click here)
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)