Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2111    Throttle Actuator Control System - Stuck Open

DTC    P2112    Throttle Actuator Control System - Stuck Closed

for Preparation Click here


SYSTEM DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC Code
DTC Detection Condition
Trouble Area
P2111
ECM signals throttle actuator to close, but stuck
(1 trip detection logic)
  1. Throttle actuator
  2. Throttle body
  3. Throttle valve
  4. ECM
P2112
ECM signals throttle actuator to open, but stuck
(1 trip detection logic)
  1. Throttle actuator
  2. Throttle body
  3. Throttle valve
  4. ECM


MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

MONITOR STRATEGY


Related DTCs
P2111: Throttle actuator stuck open
P2112: Throttle actuator stuck closed
Required Sensors/Components (Main)
Throttle actuator
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

P2111 (Throttle actuator stuck open): 
All of following conditions are met:
-
System guard*
ON
Throttle actuator current
2 A or more
Duty cycle to close throttle
80% or more

P2112 (Throttle actuator stuck closed): 
All of following conditions are met:
-
System guard*
ON
Throttle actuator current
2 A or more
Duty cycle to open throttle
80% or more
*System guard set when following conditions are met:
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

TYPICAL MALFUNCTION THRESHOLDS


P2111 (Throttle actuator stuck open): 
TP sensor voltage change for 0.016 seconds
Less than 0.1 V for 0.5 seconds or more

P2112 (Throttle actuator stuck closed): 
TP sensor voltage change for 0.016 seconds
Less than 0.1 V for 0.5 seconds or more

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned OFF.

WIRING DIAGRAM

Refer to DTC P2102 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 or P2112)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2111 or P2112
    A
    P2111 or P2112 and other DTCs
    B

    HINT:
    If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THROTTLE BODY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and the housing. If necessary, clean the throttle body. And check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.



NG
REPLACE THROTTLE BODY ASSEMBLY (Click here)
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine, and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No DTC
    A
    P2111 or P2112
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)