Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0327    Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0328    Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

DTC    P0332    Knock Sensor 2 Circuit Low Input (Bank 2)

DTC    P0333    Knock Sensor 2 Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

Flat type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 6 kHz and 15 kHz.
A knock sensor is fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC Code
DTC Detection Condition
Trouble Area
P0327
P0332
Output voltage of knock sensor less than 0.5 V
(1 trip detection logic)
  1. Short in knock sensor circuit
  2. Knock sensor
  3. ECM
P0328
P0333
Output voltage of knock sensor more than 4.5 V
(1 trip detection logic)
  1. Open in knock sensor circuit
  2. Knock sensor
  3. ECM

HINT:
When any of DTCs P0327, P0328, P0332 and P0333 are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned OFF.

Reference: Inspection using an oscilloscope
A085286E27
The correct waveform is as shown.
Item
Content
Terminal
KNK1 - EKNK
KNK2 - EKN2
Equipment Setting
1 V/DIV.
1 msec./DIV.
Condition
Keep engine speed at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and sets a DTC.
The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run when 5 seconds have elapsed since the engine was started.
If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is set 5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0327: Knock sensor (bank 1) range check (Low voltage)
P0328: Knock sensor (bank 1) range check (High voltage)
P0332: Knock sensor (bank 2) range check (Low voltage)
P0333: Knock sensor (bank 2) range check (High voltage)
Required Sensors/Components (Main)
Knock sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or more
Time after engine start
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Knock Sensor Range Check (Low voltage) P0327 and P0332: 
Knock sensor voltage
Less than 0.5 V

Knock Sensor Range Check (High voltage) P0328 and P0333: 
Knock sensor voltage
More than 4.5 V

WIRING DIAGRAM


A160376E03


INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  2. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT)
A073822E23
  1. Disconnect the Da2 connector.

  1. Using lead wires, connect the connectors as follows:

Male Connector - Female Connector
Terminal 2 - Terminal 4
Terminal 5 - Terminal 6
Terminal 4 - Terminal 2
Terminal 6 - Terminal 5
  1. Warm up the engine.

  1. Run the engine at 3000 rpm for 10 seconds or more.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Display
    Proceed to
    DTC is same as when vehicle brought in
    (for example, P0327 and P0328 are output again, or P0332 and P0333 are output again)
    A
    DTC is different from when vehicle brought in
    (for example, P0327 and P0328 are output at first, but then P0332 and P0333 are output, or vice versa)
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
A130623E04
  1. Disconnect the Da2 connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    Da2 female connector 2 - D74-94 (KNK1)
    Always
    Below 1 Ω
    Da2 female connector 5 - D74-93 (EKNK)
    Always
    Below 1 Ω
    Da2 female connector 4 - D74-117 (KNK2)
    Always
    Below 1 Ω
    Da2 female connector 6 - D74-116 (EKN2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    Da2 female connector 2 or D74-94 (KNK1) - Body ground
    Always
    10 kΩ or higher
    Da2 female connector 5 or D74-93 (EKNK) - Body ground
    Always
    10 kΩ or higher
    Da2 female connector 4 or D74-117 (KNK2) - Body ground
    Always
    10 kΩ or higher
    Da2 female connector 6 or D74-116 (EKN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VOLTAGE)
A108338E15
  1. Disconnect the Da2 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Da2 female connector 2 - 5
    Ignition switch ON
    4.5 to 5.5 V
    Da2 female connector 4 - 6
    Ignition switch ON
    4.5 to 5.5 V

  1. Reconnect the Da2 connector.



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.INSPECT KNOCK SENSOR
A072922E26
  1. Disconnect the Da2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Da2 male connector 2 - 5
    20°C (68°F)
    120 to 280 kΩ
    Da2 male connector 4 - 6
    20°C (68°F)
    120 to 280 kΩ



NG
Go to step 5
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
A140663E04

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right bank side.
  2. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left bank side.

  1. Disconnect the Da2 connector.

  1. Disconnect the a1 or a2 knock sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    Da2 male connector 2 - a2-2
    Always
    Below 1 Ω
    Da2 male connector 5 - a2-1
    Always
    Below 1 Ω
    Da2 male connector 4 - a1-2
    Always
    Below 1 Ω
    Da2 male connector 6 - a1-1
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    Da2 male connector 2 or a2-2 - Body ground
    Always
    10 kΩ or higher
    Da2 male connector 5 or a2-1 - Body ground
    Always
    10 kΩ or higher
    Da2 male connector 4 or a1-2 - Body ground
    Always
    10 kΩ or higher
    Da2 male connector 6 or a1-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)