Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil.
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC Code
DTC Detection Condition
Trouble Area
P0335
When either condition below is met:
  1. No CKP sensor signal to ECM while cranking (1 trip detection logic)
  2. No CKP sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more
(1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have elapsed since starter signal switched from ON to OFF
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM

  1. A107148E11
    Reference: Inspection using an oscilloscope.

    HINT:
    1. The correct waveform is as shown.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
    3. Grounding failure of the shielded wire may cause noise in waveforms.

    Item
    Content
    Terminal
    VV1+ - VV1-
    VV2+ - VV2-
    NE+ - NE-
    Equipment Setting
    5 V/DIV.,
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If there is no signal from the CKP sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is set 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: CKP sensor range check or rationality
Required Sensors/Components (Main)
CKP sensor
Required Sensors/Components (Related)
VVT sensor
Frequency of Operation
Continuous
Duration
3 times
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1: 
Monitor runs whenever following DTCs not present
P0340, P0342, P0343 (VVT Sensor)
Time after starter OFF to ON
3 seconds or more
Number of VVT sensor signal pulse
6 times
Battery voltage
7 V or more
Ignition switch
ON

Case 2: 
Starter
OFF
Engine speed
600 rpm or more
Time after starter from ON to OFF
3 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Case 1: 
Number of CKP sensor signal pulse
132 or less, and 174 or more

Case 2: 
Engine speed signal
No signal

COMPONENT OPERATING RANGE


CKP sensor
  1. CKP sensor output voltage fluctuates while crankshaft revolving
  2. 34 CKP sensor signals per crankshaft revolution

WIRING DIAGRAM


A160378E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  2. Check the engine speed. The engine speed can be checked by using the Techstream. To check, follow the operation below:
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream ON.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the Techstream while the engine is running.

    Standard:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the Techstream.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the Crankshaft Position (CKP) sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
A078431E25
  1. Disconnect the D4 Crankshaft Position (CKP) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    1630 to 2740 Ω
    1 - 2
    Hot
    2065 to 3225 Ω

    HINT:
    The terms "Cold" and "Hot" refer to the temperature of the sensor. Cold means approximately -10 to 50°C (14 to 122°F). Hot means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A107850E06
  1. Disconnect the D4 CKP sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D4-1 - D74-110 (NE+)
    Always
    Below 1 Ω
    D4-2 - D74-111 (NE-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D4-1 or D74-110 (NE+) - Body ground
    Always
    10 kΩ or higher
    D4-2 or D74-111 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E25
  1. Check the CKP sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


5.CHECK CRANK ANGLE SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P0335 or P0339
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END