Home › ENGINE · 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0136    Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

DTC    P0137    Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)

DTC    P0138    Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)

DTC    P0139    Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2)

DTC    P0156    Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)

DTC    P0157    Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)

DTC    P0158    Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)

DTC    P0159    Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2)

for Preparation Click here


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E07


DTC No.
DTC Detection Condition
Trouble Area
P0136
P0156
  1. Abnormal voltage output:
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) Heated Oxygen (HO2) sensor voltage does not decrease to less than 0.21 V
    1. (b) HO2 sensor voltage does not increase to more than 0.59 V
  1. Low impedance:
    1. Sensor impedance less than 5 Ω for more than 30 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)
  1. Open or short in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (for Bank 1, 2)
  3. HO2 sensor heater (for Bank 1, 2)
  4. Air-fuel Ratio (A/F) sensor (for Bank 1, 2)
  5. Integration relay
  6. Gas leakage from exhaust system
P0137
P0157
  1. Low voltage (open):
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) HO2 sensor voltage output less than 0.21 V
    1. (b) Target air-fuel ratio rich
  1. High impedance:
    1. Sensor impedance 15 kΩ or more for more than 90 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)
  1. Open in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (for Bank 1, 2)
  3. HO2 sensor heater (for Bank 1, 2)
  4. Integration relay
  5. Gas leakage from exhaust system
P0138
P0158
  1. High voltage (short):
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) HO2 sensor voltage output more than 0.59 V
    1. (b) Target air-fuel ratio lean
  1. Extremely high voltage (short):
    1. HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
  1. Short in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (for Bank 1, 2)
  3. ECM internal circuit malfunction
  4. Air-Fuel ratio (A/F) sensor (for Bank 1, 2)
P0139
P0159
The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts.
  1. Short in HO2 sensor (for Bank 1, 2 Sensor 2) circuit
  2. HO2 sensor (for Bank 1, 2 Sensor 2)
  3. ECM

MONITOR DESCRIPTION

  1. Active Air-Fuel Ratio Control
    The ECM usually performs air-fuel ratio feedback control so that the Air-Fuel Ratio (A/F) sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).
    Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.
  1. Abnormal Voltage Output of HO2 Sensor (DTC P0136 and P0156)
    While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not decrease to less than 0.21 V and does not increase to more than 0.59 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.

    A115540E08

  1. Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157 or P0138 and P0158)
    During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the HO2 sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.
    While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is below 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157. When the target air-fuel ratio is lean and the voltage output is higher than 0.59 V (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high, and stores DTC P0138 or P0158.

    HINT:
    DTC P0138 or P0158 is also stored if the HO2 sensor voltage output is more than 1.2 V for 10 seconds or more.

    *: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value .

    A115541E11

  1. High or Low Impedance of Heated Oxygen (HO2) Sensor (DTC P0136 and P0156 or P0137 and P157)
    A076841E13
    During normal air-fuel ratio feedback control, there are small variations in the exhaust gas oxygen concentration. In order to continuously monitor the slight variations in the HO2 sensor signal while the engine is running, the impedance* of the sensor is measured by the ECM. The ECM determines that there is a malfunction in the sensor when the measured impedance deviates from the standard range.
    *: The effective resistance in an alternating current electrical circuit.

    HINT:
    1. The impedance cannot be measured using an ohmmeter.
    2. DTC P0136 and P0156 indicate the deterioration of the HO2 sensor. The ECM sets this DTC by calculating the impedance of the sensor when the typical enabling conditions are satisfied (2 driving cycles).
    3. DTC P0137 and P0157 indicate an open or short circuit in the HO2 sensor (2 driving cycles). The ECM stores this DTC when the impedance of the sensor exceeds the threshold 15 kΩ.

  1. HO2 sensor output voltage during fuel cut (P0139 or P0159)
    The sensor voltage drops below 0.2 V (extremely lean status) immediately when the vehicle decelerates and fuel cut is operating. If the voltage does not drop below 0.2 V, the ECM determines that the sensor response feature has deteriorated, illuminates the MIL and stores DTC(s).

MONITOR STRATEGY


Related DTCs
P0136: Heated oxygen sensor (for Bank 1) output voltage (Abnormal voltage output)
P0136: Heated oxygen sensor (for Bank 1) impedance (Low)
P0137: Heated oxygen sensor (for Bank 1) output voltage (Low voltage)
P0137: Heated oxygen sensor (for Bank 1) impedance (High)
P0138: Heated oxygen sensor (for Bank 1) output voltage (High voltage)
P0138: Heated oxygen sensor (for Bank 1) output voltage (Extremely high)
P0139: Heated oxygen sensor (for Bank 1) output voltage during fuel cut
P0156: Heated oxygen sensor (for Bank 2) output voltage (Abnormal voltage output)
P0156: Heated oxygen sensor (for Bank 2) impedance (Low)
P0157: Heated oxygen sensor (for Bank 2) output voltage (Low voltage)
P0157: Heated oxygen sensor (for Bank 2) impedance (High)
P0158: Heated oxygen sensor (for Bank 2) output voltage (High voltage)
P0158: Heated oxygen sensor (for Bank 2) output voltage (Extremely high)
P0159: Heated oxygen sensor (for Bank 2) output voltage during fuel cut
Required Sensors/Components (Main)
Heated oxygen sensor
Required Sensors/Components (Related)
Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and throttle position sensor
Frequency of Operation
Once per driving cycle: Active air-fuel ratio control detection, Heated oxygen sensor voltage (During fuel cut)
Continuous: Other
Duration
20 seconds: Active air-fuel ratio control detection
90 seconds: Heated oxygen sensor impedance (High)
30 seconds: Heated oxygen sensor impedance (Low)
10 seconds: Output voltage (Stuck high)
9 seconds: Heated oxygen sensor voltage (During fuel cut)
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Heated Oxygen Sensor Output Voltage (Abnormal Voltage Output, High Voltage and Low Voltage) 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
Active air-fuel ratio control
Executing
Active air-fuel ratio control begins when all of following conditions met:
-
Battery voltage
11 V or more
Engine coolant temperature
75°C (167°F) or more
Idling
OFF
Engine speed
Less than 3200 rpm
A/F sensor status
Activated
Fuel system status
Closed loop
Fuel cut
OFF
Engine load
10 to 75%
Transmission gear
4th or higher

Heated Oxygen Sensor Impedance (Low) 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0607 (Rear Oxygen Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
Battery voltage
11 V or more
Estimated rear HO2 sensor temperature
Less than 700°C (1292°F)
ECM monitor
Completed
DTC P0607
Not set

Heated Oxygen Sensor Impedance (High) 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0607 (Rear Oxygen Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
Battery voltage
11 V or more
Estimated rear HO2 sensor temperature
450 to 750°C (842 to 1382°F)
ECM monitor
Completed
DTC P0607
Not set

Heated Oxygen Sensor Output Voltage (Extremely High) 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
Battery voltage
11 V or more
Time after engine start
2 seconds or more

Heated Oxygen Sensor Output Voltage During Fuel Cut 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
Engine coolant temperature
75°C (167°F) or higher
Estimated catalyst temperature
400°C (752°F) or more
Fuel cut
ON

TYPICAL MALFUNCTION THRESHOLDS


Heated Oxygen Sensor Output Voltage (Abnormal Voltage Output): 
Either of following conditions met:
1 or 2
1. All of following conditions (a), (b) and (c) met
-
(a) Commanded air-fuel ratio
14.3 or less
(b) Rear HO2 sensor voltage
0.21 to 0.59 V
(c) OSC (Oxygen Storage Capacity of Catalyst)
2.5 g or more
2. All of following conditions (d), (e) and (f) met
-
(d) Commanded air-fuel ratio
14.9 or more
(e) Rear HO2 sensor voltage
0.21 to 0.59 V
(f) OSC
2.5 g or more

Heated Oxygen Sensor Output Voltage (Low): 
All of following conditions (a), (b) and (c) met
-
(a) Commanded air-fuel ratio
14.3 or less
(b) Rear HO2 sensor voltage
Less than 0.21 V
(c) OSC
2.5 g or more

Heated Oxygen Sensor Output Voltage (High): 
All of following conditions (a), (b) and (c) met
-
(a) Commanded air-fuel ratio
14.9 or more
(b) Rear HO2 sensor voltage
More than 0.59 V
(c) OSC
2.5 g or more

Heated Oxygen Sensor Impedance (Low): 
Duration of following condition met
30 seconds or more
Heated oxygen sensor impedance
Less than 5 Ω

Heated Oxygen Sensor Impedance (High): 
Duration of following condition met
90 seconds or more
Heated oxygen sensor impedance
15 kΩ or more

Heated Oxygen Sensor Output Voltage (Extremely High): 
Duration of following condition met
10 seconds or more
Heated oxygen sensor voltage
1.2 V or more

Heated Oxygen Sensor Output Voltage during fuel cut: 
Duration until rear heated oxygen sensor voltage drops to 0.2 V during fuel cut
9 seconds or more

COMPONENT OPERATING RANGE


Duration of following condition met
30 seconds or more
Heated oxygen sensor voltage
Varies between 0.1 and 0.9 V

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM


A167571E01


CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation driving pattern will activate the Heated Oxygen (HO2) sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.

NOTICE:
This test will not be completed if the vehicle is driven under absolutely constant speed conditions such as with cruise control activated.


A197674E01

  1. Connect the Techstream to the DLC3.
  2. Clear the DTC (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  3. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  4. Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more [A].
  5. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more [B].

    HINT:
    Make sure that the Data List "Alcohol Density Learning" is "Compl".

  6. Drive the vehicle at between 60 and 120 km/h (40 and 75 mph) and maintain a constant speed for at least 10 minutes [C].

    CAUTION:
    Perform this drive pattern on a level road as much as possible and strictly observe the posted speed limits and traffic laws while driving.

  7. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times [D].
  8. Turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Enter the following DTCs: P0136, P0137, P0138, P0139, P0156, P0157, P0158 and P0159.
  11. Check that the DTC monitor is "NORMAL". If the DTC monitor is "INCOMPLETE", perform the drive pattern increasing the vehicle speed and using the second gear to decelerate the vehicle [D].

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the following procedure.
  1. Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
  2. Connect the Techstream to the DLC3.
  3. Stop the engine.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Write down the freeze frame data.
  7. Clear the DTCs (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  8. Enter the following menus: Powertrain / Engine and ECT / Data List / Flexible Fuel Vehicle.
  9. Record data using snapshots.
  10. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  11. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more.
  12. After this driving make sure that the Data List "Alcohol Density Learning" is "Compl".
  13. While the engine is idling, monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
    Result 
    Result
    Main Suspected Trouble Area
    A/F sensor output between 3.1 and 3.4 V
    and
    O2 sensor output slowly changes in the range of 0 and 1 V
    and
    Aggregate fuel trim*1 between -20 and 65%
    -
    A/F sensor output consistently outside range of 3.1 to 3.4 V
    and
    O2 sensor output and A/F sensor output contradict each other*2
    1. A/F sensor
    2. A/F sensor heater
    3. A/F sensor circuit
    A/F sensor output between 3.1 and 3.4 V
    and
    O2 sensor output consistently indicates rich or lean
    1. HO2 sensor
    2. HO2 sensor heater
    3. HO2 sensor circuit
    A/F sensor and O2 sensor output both consistently indicate rich or lean
    or
    Aggregate fuel trim*1 less than -20%
    or
    Aggregate fuel trim*1 more than 65%
    1. Injector
    2. Fuel pressure
    3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

    HINT:
    1. *1: Aggregate fuel trim is approximately equal to the following: Short FT + ((1 + Long FT / 100) x (1 + (Alcohol Density Estimate / 2 / 100)) - 1) x 100
    2. *2: For example, the A/F sensor output indicates rich while the O2 sensor output indicates lean.
    3. Sensor Output Reference Values
      Air-fuel Ratio
      A/F Sensor
      HO2 Sensor
      Lean
      Higher than 3.25 V
      Below 0.4 V
      Rich
      Below 3.25 V
      Higher than 0.55 V
    4. Reference values when normal (E0 Fuel)
      AFS Voltage B1 S1
      3.28 V
      AFS Voltage B2 S1
      3.28 V
      O2S B1 S2
      0.76 V
      O2S B2 S2
      0.70 V
      Short FT #1
      1%
      Long FT #1
      -6%
      Short FT #2
      2%
      Long FT #2
      -6%
      AF Lambda B1 S1
      0.99
      AF Lambda B2 S1
      0.99
      Alcohol Density Estimate
      0%
      Alcohol Density Learning
      Compl
    5. Reference values when A/F sensor (Bank 1) is malfunctioning (E0 Fuel)
      AFS Voltage B1 S1
      4.99 V
      AFS Voltage B2 S1
      3.25 V
      O2S B1 S2
      0.95 V
      O2S B2 S2
      0.74 V
      Short FT #1
      0%
      Long FT #1
      17.1%
      Short FT #2
      0%
      Long FT #2
      -6.3%
      AF Lambda B1 S1
      1.23
      AF Lambda B2 S1
      0.99
      Alcohol Density Estimate
      41%
      Alcohol Density Learning
      Compl
    6. Reference values when purge hose disconnected (both banks are lean) (E0 Fuel)
      AFS Voltage B1 S1
      3.45 V
      AFS Voltage B2 S1
      3.56 V
      O2S B1 S2
      0.03 V
      O2S B2 S2
      0.03 V
      Short FT #1
      20.3%
      Long FT #1
      -1.6%
      Short FT #2
      19.5%
      Long FT #2
      -6.3%
      AF Lambda B1 S1
      1.04
      AF Lambda B2 S1
      1.08
      Alcohol Density Estimate
      85%
      Alcohol Density Learning
      Compl
    7. Reference values when HO2 sensor (Bank 1) is malfunctioning (E0 Fuel)
      AFS Voltage B1 S1
      3.23 V
      AFS Voltage B2 S1
      3.28 V
      O2S B1 S2
      0.00 V
      O2S B2 S2
      0.68 V
      Short FT #1
      0%
      Long FT #1
      -1.6%
      Short FT #2
      2%
      Long FT #2
      -6.3%
      AF Lambda B1 S1
      0.99
      AF Lambda B2 S1
      0.99
      Alcohol Density Estimate
      0%
      Alcohol Density Learning
      Compl

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be set.
  4. If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be set.

1.READ OUTPUT DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0138 or P0158 is output
    A
    P0137 or P0157 is output
    B
    P0136 or P0156 is output
    C
    P0139 or P0159 is output
    D

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or more.

  1. Clear DTC (Click here).

  1. Start the engine.

    HINT:
    After clearing the DTCs, the engine becomes difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  1. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more.

  1. After this driving make sure that the Data List "Alcohol Density Learning" is "Compl".



B
Go to step 16

C
Go to step 6

D
Go to step 24
A


2.READ VALUE TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.

  1. Allow the engine to idle.

  1. Read the Heated Oxygen (HO2) sensor output voltage while idling.

    Standard voltage:
    Less than 1.0 V



OK
Go to step 5

NG
Go to step 3

3.INSPECT HEATED OXYGEN SENSOR
A117841E29
  1. Disconnect the D31 or D32 HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E1)
    Always
    10 kΩ or higher
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E1)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A136305E21
  1. Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D74-45 (HT1B) - D74-114 (OX1B)
    Always
    10 kΩ or higher
    D74-44 (HT2B) - D74-112 (OX2B)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK AIR FUEL RATIO SENSOR

HINT:
This A/F sensor test is to check the A/F sensor current during the fuel-cut. When the sensor is normal, the sensor current will indicate below 3 mA in this test.

  1. Clear DTC (Click here).



  1. Drive the vehicle by the drive pattern as listed below:

    1. Warm up the engine.



    2. Accelerator the vehicle until 60 km/h (40 mph) or more and decelerate for 5 seconds or more.


      A166560E05

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details.

  1. Confirm that RANGE B1S1 and RANGE B2S1 are either PASS or FAIL. If the Techstream shows incomplete, Re-check RANGE B1S1 and RANGE B2S1 after performing the drive pattern.

    HINT:
    1. If the Techstream shows complete, it not necessary to continue the driving pattern.
    2. If the Techstream shows incomplete again, add the vehicle speed and use the second gear to decelerate the vehicle.

  1. Select RANGE B1S1 and press ENTER.

  1. Read the test value.

    Standard current:
    Less than 3.0 mA

    NOTICE:
    Do not turn the ignition switch off during this step because the test results will be lost.



OK
Go to step 20

NG
Go to step 22

6.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.

  1. After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.

  1. Read the output voltage of the HO2 sensor when the engine speed is suddenly increased.

    HINT:
    Quickly accelerate the engine to 4000 rpm 3 times using the accelerator pedal.

    Standard voltage:
    Fluctuates between 0.4 V or less and 0.5 V or more.



NG
Go to step 16
OK


7.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the Techstream, and monitor the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.

  2. The A/F sensor is displayed as AFS Voltage B1 S1 or AFS Voltage B2 S1, and the HO2 sensor is displayed as O2S B1 S2 or O2S B2 S2, on the Techstream.

    Result 
    Display Item (Sensor)
    Voltage Variation
    Proceed to
    AFS Voltage B1 S1 (A/F)
    AFS Voltage B2 S1 (A/F)
    Alternates between more and less than 3.3 V
    OK
    Remains at more than 3.3 V
    NG
    Remains at less than 3.3 V
    NG

    HINT:
    A normal HO2 sensor voltage (O2S B1 S2 or O2S B2 S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.



    A121606E03



NG
Go to step 22
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


9.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
GO TO FUEL PRESSURE SWITCHING SYSTEM (Click here)
OK


10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
  1. Check the injection volume .



NG
REPLACE FUEL INJECTOR (Click here)
OK


11.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter .



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


12.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor .



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


13.INSPECT PCV HOSE
  1. Check the PCV hose connections .

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


14.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


15.CHECK SPARKS AND IGNITION
A151834
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE IGNITION SYSTEM (Click here)
OK

REPLACE ECM (Click here)  

16.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


17.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A117841E28
  1. Disconnect the D31 or D32 HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E1)
    Always
    10 kΩ or higher
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E1)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


18.INSPECT INTEGRATION RELAY (EFI RELAY)
A148742E04
  1. Remove the integration relay from the engine room relay block .

  1. Inspect the EFI NO. 1 fuse.

    1. Remove the EFI NO. 1 fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI NO. 1 fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI NO. 1 fuse.

  1. Inspect the EFI relay.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      When no battery voltage applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      When battery voltage applied to terminals 1B-2 and 1B-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


19.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A164723E01

A164717E01

  1. Disconnect the D31 or D32 HO2 sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D31-2 (+B) - Body ground
    Ignition switch ON
    9 to 14 V
    D32-2 (+B) - Body ground
    Ignition switch ON
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D31-1 (HT1B) - D74-45 (HT1B)
    Always
    Below 1 Ω
    D31-3 (OX1B) - D74-114 (OX1B)
    Always
    Below 1 Ω
    D31-4 (E1) - D74-115 (EX1B)
    Always
    Below 1 Ω
    D32-1 (HT2B) - D74-44 (HT2B)
    Always
    Below 1 Ω
    D32-3 (OX2B) - D74-112 (OX2B)
    Always
    Below 1 Ω
    D32-4 (E1) - D74-113 (EX2B)
    Always
    Below 1 Ω
    D31-1 (HT1B) or D74-45 (HT1B) - Body ground
    Always
    10 kΩ or higher
    D31-3 (OX1B) or D74-114 (OX1B) - Body ground
    Always
    10 kΩ or higher
    D32-1 (HT2B) or D74-44 (HT2B) - Body ground
    Always
    10 kΩ or higher
    D32-3 (OX2B) or D74-112 (OX2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


20.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


21.PERFORM CONFIRMATION DRIVING PATTERN

A197674E01

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [A].

  1. Stop the engine.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream to on.

  1. Clear the DTC (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  1. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  1. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more [B].

    HINT:
    Make sure that the Data List "Alcohol Density Learning" is "Compl".

  1. Drive the vehicle at 60 to 120 km/h (40 to 75 mph) and maintain a constant speed for at least 10 minutes [C].

    CAUTION:
    Perform this drive pattern on a level road as much as possible and strictly observe the posted speed limits and traffic laws while driving.

  1. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times [D].

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Enter the following DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check that the DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using the second gear to decelerate the vehicle [D].

    OK:
    No DTC is output.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK

REPAIR COMPLETE 

22.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


23.PERFORM CONFIRMATION DRIVING PATTERN

A197674E01

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [A].

  1. Stop the engine.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream to on.

  1. Clear the DTC (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  1. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  1. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more [B].

    HINT:
    Make sure that the Data List "Alcohol Density Learning" is "Compl".

  1. Drive the vehicle at 60 to 120 km/h (40 to 75 mph) and maintain a constant speed for at least 10 minutes [C].

    CAUTION:
    Perform this drive pattern on a level road as much as possible and strictly observe the posted speed limits and traffic laws while driving.

  1. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times [D].

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Enter the following DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check that the DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using the second gear to decelerate the vehicle [D].

    OK:
    No DTC is output.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK

REPAIR COMPLETE 

24.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.

  1. After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.

  1. Engine is idling.

  1. Depress the accelerator pedal quickly until the engine speed reaches 2500 rpm 3 times.
    Result 
    Result
    Proceed to
    1.0 V or higher
    A
    Below 1.0 V
    B



B
Go to step 27
A


25.INSPECT HEATED OXYGEN SENSOR
A117841E29
  1. Disconnect the D31 or D32 HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E1)
    Always
    10 kΩ or higher
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E1)
    Always
    10 kΩ or higher



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


26.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
A136305E21
  1. Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D74-45 (HT1B) - D74-114 (OX1B)
    Always
    10 kΩ or higher
    D74-44 (HT2B) - D74-112 (OX2B)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

27.PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Refer to the CONFIRMATION DRIVING PATTERN


NEXT


28.READ DTC OUTPUT (DTC P0139 OR P0159 IS OUTPUT AGAIN)
  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0139 or P0159 is output
    A
    No DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HEATED OXYGEN SENSOR (Click here)