Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).
The VVT camshaft drive gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each engine revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC Code
DTC Detection Condition
Trouble Area
P0340
P0345
When either condition below is met:
  1. Input voltage to ECM remains less than 0.3 V, or more than 4.7 V for 4 seconds, when 2 or more seconds have elapsed after turning ignition switch ON
    (1 trip detection logic)
  2. No VVT sensor signal to ECM during cranking
    (2 trip detection logic)
  1. Open or short in VVT sensor circuit
  2. VVT sensor
  3. Camshaft timing gear
  4. Jumped tooth of timing chain
  5. ECM
P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)

  1. A107148E11
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is as shown.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.

    Item
    Content
    Terminal
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Setting
    5 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (Bank 1) range check
P0340: Camshaft position/Crankshaft position misalignment (Bank 1)
P0340: VVT sensor (Bank 1) range check (fluctuating)
P0342: VVT sensor (Bank 1) range check (low voltage)
P0343: VVT sensor (Bank 1) range check (high voltage)
P0345: VVT sensor (Bank 2) range check (while starting engine)
P0345: VVT sensor (Bank 2) range check (after starting engine)
P0345: VVT sensor (Bank 2) range check (fluctuating)
P0347: VVT sensor (Bank 2) range check (low voltage)
P0348: VVT sensor (Bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT sensors (Banks 1 and 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
4 seconds:
P0340 (VVT sensor (Bank 1) range check and VVT sensor (Bank 1) range check [fluctuating]), P0342, P0343 and P0345 (VVT sensor range check [while starting engine])
5 seconds:
Others
MIL Operation
2 driving cycles: P0340 (cranking), P0345 (cranking)
MIL Operation P0340 (VVT sensor range check), P0345 (VVT sensor range check [while starting engine])
Immediate:
Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

VVT Sensor Range Check: 
Starter
ON
Minimum battery voltage while starter ON
Less than 11 V

Camshaft Position/Crankshaft Position Misalignment: 
Engine RPM
600 rpm or more
Starter
OFF

VVT Sensor Range Check (Fluctuating, Low voltage, High voltage): 
Starter
OFF
Ignition switch ON and time after ignition switch changed from OFF to ON
2 seconds or more

VVT Sensor Range Check (While starting engine): 
Starter
ON
Battery voltage while starter ON once at least
Less than 11 V

VVT Sensor Range Check (After starting engine): 
Engine RPM
600 rpm or more
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

VVT Sensor Range Check (Fluctuating, Low voltage, High voltage): 
Starter
OFF
Ignition switch ON and time after ignition switch changed from OFF to ON
2 seconds or more
Battery voltage
8 V or more

TYPICAL MALFUNCTION THRESHOLDS


VVT Sensor Range Check: 
VVT sensor signal No signal
No signal

Camshaft Position/Crankshaft Position Misalignment: 
Camshaft position and crankshaft position phases
Misaligned

VVT Sensor Range Check (Fluctuating): 
VVT sensor voltage
Less than 0.3 V, or more than 4.7 V

VVT Sensor Range Check (Low voltage): 
VVT sensor voltage
Less than 0.3 V

VVT Sensor Range Check (High voltage): 
VVT sensor voltage
More than 4.7 V

VVT Sensor Range Check (While starting engine): 
VVT sensor signal
No signal

VVT Sensor Range Check (After starting engine): 
VVT sensor signal
No signal

VVT Sensor Range Check (Fluctuating): 
VVT sensor voltage
Less than 0.3 V, or more than 4.7 V

VVT Sensor Range Check (Low voltage): 
VVT sensor voltage
Less than 0.3 V

VVT Sensor Range Check (High voltage): 
VVT sensor voltage
More than 4.7 V

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

WIRING DIAGRAM


A160377E04


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK VVT SENSOR (SENSOR POWER SOURCE)


    A202811E01
  1. Disconnect the D79 or D78 VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D79-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V
    D78-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)


    A130624E11
  1. Disconnect the D79 or D78 VVT sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D79-1 (VVR+) - D74-90 (VV1+)
    Always
    Below 1 Ω
    D79-2 (VVR-) - D74-89 (VV1-)
    Always
    Below 1 Ω
    D78-1 (VVL+) - D74-87 (VV2+)
    Always
    Below 1 Ω
    D78-2 (VVL-) - D74-88 (VV2-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D79-1 (VVR+) or D74-90 (VV1+) - Body ground
    Always
    10 kΩ or higher
    D79-2 (VVR-) or D74-89 (VV1-) - Body ground
    Always
    10 kΩ or higher
    D78-1 (VVL+) or D74-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    D78-2 (VVL-) or D74-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)


    BR03795E17
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.CHECK VALVE TIMING


    G036290E11
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover .



NG
ADJUST VALVE TIMING
OK


5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


6.REPLACE VVT SENSOR
  1. Replace VVT sensor .


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END