Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the Air-Fuel Ratio (A/F) sensor, sends pre-catalyst information to the ECM. The second sensor, the Heated Oxygen (HO2) sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the HO2 sensor while performing active air-fuel ratio control.
The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If a rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.
The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and sets a DTC.

DTC Code
DTC Detection Condition
Trouble Area
P0420
OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
  1. Gas leakage from exhaust system
  2. A/F sensor (bank 1 sensor 1)
  3. HO2 sensor (bank 1 sensor 2)
  4. Exhaust pipe assembly
P0430
OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
  1. Gas leakage from exhaust system
  2. A/F sensor (bank 2 sensor 1)
  3. HO2 sensor (bank 2 sensor 2)
  4. Front No. 2 exhaust pipe assembly (for Regular Cab Standard Deck)
  5. Front exhaust pipe assembly (except Regular Cab Standard Deck)
  6. Front No. 3 exhaust pipe sub-assembly (except Regular Cab Standard Deck)

HINT:
  1. Bank 1 refers to the bank that includes No. 1 cylinder.
  2. Bank 2 refers to the bank that does not include No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR STRATEGY


Related DTCs
P0420: Catalyst Deterioration
P0430: Catalyst Deterioration
Required Sensors/Components (Main)
A/F sensor and heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
About 30 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0136, P0137, P0138, P0139, P0156, P0157, P0158, P0159, P0606, P0607 (Rear Oxygen Sensor)
P0102, P0103 (Mass Air Flow Meter)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0351 - P0356 (Igniter)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2246, P2247 (Secondary Air Injection System)
P0500 (Vehicle Speed Sensor)
Battery voltage
11 V or more
IAT
-10°C (14°F) or more
Engine coolant temperature sensor
75°C (167°F) or more
Atmospheric pressure coefficient
76 kPa (570 mmHg) or more
Idling
OFF
Engine RPM
Less than 3200 rpm
A/F sensor status
Activated
Fuel system status
Closed loop
Engine load
10 to 80%
All of the following conditions are met
Condition 1, 2 and 3
1. Mass air flow rate
5 to 70 g/sec.
2. Front catalyst temperature (estimated)
600 to 840°C (1112 to 1544°F)
3. Rear catalyst temperature (estimated)
100 to 900°C (212 to 1652°F)
Rear HO2 sensor monitor
Completed
Shift position
4th or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC)
Less than 0.008 g

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation pattern will activate the catalyst monitor. This is very useful for verifying the completion of a repair.


A115372E94

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Turn the ignition switch ON.
  3. (c) Turn the Techstream ON.
  4. (d) Clear DTCs (if set) (Click here).
  5. (e) Enter the following menus: Powertrain / Engine and ECT / Monitor.
  6. (f) Check that Catalyst / Status2 is Incomplete.
  7. (g) Start the engine and warm it up.
  8. (h) Drive the vehicle at between 40 mph and 70 mph (64 km/h and 113 km/h) for at least 10 minutes.
  9. (i) Those items will change to Complete as Catalyst monitor operates.
  10. (j) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
  11. (k) Check if any DTCs (any pending DTCs) are set.

HINT:
If Catalyst does not change to Complete, and any pending DTCs fail to set, extend the driving time.


CONDITIONING FOR SENSOR TESTING


HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the A/F and HO2 sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.

A118003E14

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine and warm it up with all the accessories switched OFF until the engine coolant temperature stabilizes.
  3. (c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
  4. (d) While running the engine at 3000 rpm for 2 seconds and 2000 rpm for 2 seconds, check the waveforms of the A/F and HO2 sensors using the Techstream.


HINT:
  1. If either of the voltage outputs of the Air-Fuel Ratio (A/F) or Heated Oxygen (HO2) sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  3. If the Three-Way Catalytic Converter (TWC) has deteriorated, the HO2 sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).

A121610E09


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Start the engine and turn the Techstream ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E05
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E05
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0420 and/or P0430
    A
    P0420 and/or P0430 and other DTCs
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream ON.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

  1. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

      Standard:

      Tester Display
      (Sensor)
      Injection Volume
      Status
      Voltage
      AFS Voltage B1S1 or AFS Voltage B2S1
      (A/F)
      +25%
      Rich
      Less than 3.1
      AFS Voltage B1S1 or AFS Voltage B2S1
      (A/F)
      -12.5%
      Lean
      More than 3.4
      O2S B1S2 or O2S B2S2
      (HO2)
      +25%
      Rich
      More than 0.55
      O2S B1S2 or O2S B2S2
      (HO2)
      -12.5%
      Lean
      Less than 0.4


      Result:

      Status
      AFS Voltage B1S1
      or
      AFS Voltage B2S1
      Status
      O2S B1S2
      or
      O2S B2S2
      A/F Condition and A/F and
      HO2 Sensors Condition
      Misfire
      Main Suspected Trouble Area
      Proceed to
      Lean/Rich
      Lean/Rich
      Normal
      -
      1. Three-Way Catalytic Converter (TWC)
      2. Gas leakage from exhaust system
      A
      Lean
      Lean/Rich
      A/F sensor malfunction
      -
      1. A/F sensor
      B
      Rich
      Lean/Rich
      A/F sensor malfunction
      -
      1. A/F sensor
      Lean/Rich
      Lean
      HO2 sensor malfunction
      -
      1. HO2 sensor
      2. Gas leakage from exhaust system
      C
      Lean/Rich
      Rich
      HO2 sensor malfunction
      -
      1. HO2 sensor
      2. Gas leakage from exhaust system
      Lean
      Lean
      Actual air-fuel ratio lean
      May occur
      1. Extremely rich or lean actual air-fuel ratio
      2. Gas leakage from exhaust system
      A
      Rich
      Rich
      Actual air-fuel ratio rich
      -
      1. Extremely rich or lean actual air-fuel ratio
      2. Gas leakage from exhaust system

      Lean: During Control the Injection Volume for A/F sensor, the A/F sensor output voltage (AFS) is consistently more than 3.4 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
      Rich: During Control the Injection Volume for A/F sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.
      Lean/Rich: During Control the Injection Volume for A/F sensor of the Active Test, the output voltage of the HO2 sensor alternates correctly.



B
REPLACE AIR FUEL RATIO SENSOR (Click here)

C
Go to step 4

D
CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO, REPLACE FAULTY AREA AND GO TO NEXT STEP
A


3.INSPECT FOR EXHAUST GAS LEAK

OK:
No gas leakage.

Result:
Result
Proceed to
NG
A
OK
B



B
Go to step 5
A

REPAIR OR REPLACE EXHAUST GAS LEAK POINT 

4.INSPECT EXHAUST GAS LEAK

OK:
No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK

REPLACE HEATED OXYGEN SENSOR (Click here)  

5.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
  1. According to the output DTCs in the step 1 (Check Any Other DTCs Output), proceed to next step referring to the table below.

    Result:
    Result
    Proceed to
    P0420
    A
    P0430 (for Regular Cab Standard Deck)
    B
    P0430 (except Regular Cab Standard Deck)
    C
    P0420 and P0430
    A and B or C



B
Go to step 6

C
REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (Click here)
A

REPLACE EXHAUST PIPE ASSEMBLY (Click here)  

6.REPLACE FRONT EXHAUST PIPE ASSEMBLY

NEXT

REPLACE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY (Click here)