Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. When one of these DTCs is set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  4. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


    A164715E01


DTC Code
DTC Detection Condition
Trouble Area
P0031
P0051
Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A
(1 trip detection logic)
  1. Open in A/F sensor heater circuit
  2. A/F sensor heater (for sensor 1)
  3. Integration relay
  4. ECM
P0032
P0052
Air-Fuel Ratio (A/F) sensor heater current fail
(1 trip detection logic)
  1. Short in A/F sensor heater circuit
  2. A/F sensor heater (for sensor 1)
  3. Integration relay
  4. ECM

HINT:
  1. Bank 1 refers to the bank that includes No. 1 cylinder.
  2. Bank 2 refers to the bank that does not include No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM uses information from the Air-Fuel Ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.
The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor becomes inaccurate. As a result, the ECM is unable to regulate air-fuel ratio properly.
When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and sets a DTC.
Example:
The ECM sets DTC P0032 or P0052 when the current in the A/F sensor heater is more than 10 A. Conversely, when the heater current is less than 0.8 A, DTC P0031 or P0051 is set.

MONITOR STRATEGY


Related DTCs
P0031: A/F sensor heater (bank 1) open/short (Low electrical current)
P0032: A/F sensor heater (bank 1) open/short (High electrical current)
P0051: A/F sensor heater (bank 2) open/short (Low electrical current)
P0052: A/F sensor heater (bank 2) open/short (High electrical current)
Required Sensors/Components (Main)
A/F sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
10 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
None

P0031 and P0051: 
Battery voltage
10.5 V or higher
A/F sensor heater duty-cycle ratio
50% or more
Time after engine start
10 seconds or more

P0032 and P0052: 
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051: 
A/F sensor heater current
Less than 0.8 A

P0032 and P0052: 
Hybrid IC high current limiter port
Fail

COMPONENT OPERATING RANGE


A/F sensor heater current
0.9 to 9.9 A

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
  1. Disconnect the D33 or D34 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
A150242E07
  1. Disconnect the D33 or D34 A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D33-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D34-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


3.INSPECT INTEGRATION RELAY (A/F)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

    3. Reinstall the A/F fuse.

  1. Inspect the integration relay (A/F).

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      When no battery voltage applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      When battery voltage applied to terminals 1A-2 and 1A-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY (A/F)
OK


4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)
A164716E01
  1. Disconnect the D33 or D34 A/F sensor connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D33-2 (+B) - 1A-4
    Always
    Below 1 Ω
    D34-2 (+B) - 1A-4
    Always
    Below 1 Ω
    1A-2 - 1B-5
    Always
    Below 1 Ω
    1A-3 - Body ground
    Always
    Below 1 Ω
    D33-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher
    D34-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher
    1A-2 or 1B-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E02
  1. Disconnect the D33 or D34 A/F sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) - D74-22 (HA1A)
    Always
    Below 1 Ω
    D34-1 (HA2A) - D74-20 (HA2A)
    Always
    Below 1 Ω
    D33-1 (HA1A) or D74-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D34-1 (HA2A) or D74-20 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0031, P0032, P0051 or P0052 is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)