Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil circuit.
  6. If DTC P0355 is set, check the No. 5 ignition coil circuit.
  7. If DTC P0356 is set, check the No. 6 ignition coil circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A136310E03


DTC Code
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil and ECM
  3. No. 1 to No. 6 ignition coils
  4. ECM

  1. G035664E01
  2. Reference: Inspection using an oscilloscope.
  3. While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.
    Item
    Content
    Terminal
    CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
    CH2: IGF1 - E1
    Equipment Setting
    2 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION


A115898E05

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 1 second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (cylinder 1) malfunction
P0352: Igniter (cylinder 2) malfunction
P0353: Igniter (cylinder 3) malfunction
P0354: Igniter (cylinder 4) malfunction
P0355: Igniter (cylinder 5) malfunction
P0356: Igniter (cylinder 6) malfunction
Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
About 1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions A or B met
-
A. Engine RPM
1500 rpm or less
B. Starter
OFF
Either of following conditions C or D met
-
C. Both of following conditions (a) and (b) met
-
(a) Engine speed
500 rpm or less
(b) Battery voltage
6 V or more
D. All of following conditions (a), (b) and (c) met
-
(a) Engine speed
More than 500 rpm
(b) Battery voltage
10 V or more
(c) Number of sparks after CPU reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


Ignition signal fail count
More than 2 times
Ignition signal fail count is on the right
When IGF does not return despite sending IGT

COMPONENT OPERATING RANGE


IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM

WIRING DIAGRAM


A160534E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A115969E05
  1. Disconnect the ignition coil connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D10-4 (GND) - Body ground
    Always
    Below 1 Ω
    D25-4 (GND) - Body ground
    Always
    Below 1 Ω
    D12-4 (GND) - Body ground
    Always
    Below 1 Ω
    D23-4 (GND) - Body ground
    Always
    Below 1 Ω
    D14-4 (GND) - Body ground
    Always
    Below 1 Ω
    D21-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    D10-1 (+B) - D10-4 (GND)
    Ignition switch ON
    11 to 14 V
    D25-1 (+B) - D25-4 (GND)
    Ignition switch ON
    11 to 14 V
    D12-1 (+B) - D12-4 (GND)
    Ignition switch ON
    11 to 14 V
    D23-1 (+B) - D23-4 (GND)
    Ignition switch ON
    11 to 14 V
    D14-1 (+B) - D14-4 (GND)
    Ignition switch ON
    11 to 14 V
    D21-1 (+B) - D21-4 (GND)
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
A105983E22
  1. Disconnect the ignition coil connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D10-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D25-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D12-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D23-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D14-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D21-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D10-3 (IGT1) - D74-40 (IGT1)
    Always
    Below 1 Ω
    D25-3 (IGT2) - D74-39 (IGT2)
    Always
    Below 1 Ω
    D12-3 (IGT3) - D74-38 (IGT3)
    Always
    Below 1 Ω
    D23-3 (IGT4) - D74-37 (IGT4)
    Always
    Below 1 Ω
    D14-3 (IGT5) - D74-36 (IGT5)
    Always
    Below 1 Ω
    D21-3 (IGT6) - D74-35 (IGT6)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D10-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D25-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D12-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D23-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D14-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D21-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D10-3 (IGT1) or D74-40 (IGT1) - Body ground
    Always
    10 kΩ or higher
    D25-3 (IGT2) or D74-39 (IGT2) - Body ground
    Always
    10 kΩ or higher
    D12-3 (IGT3) or D74-38 (IGT3) - Body ground
    Always
    10 kΩ or higher
    D23-3 (IGT4) or D74-37 (IGT4) - Body ground
    Always
    10 kΩ or higher
    D14-3 (IGT5) or D74-36 (IGT5) - Body ground
    Always
    10 kΩ or higher
    D21-3 (IGT6) or D74-35 (IGT6) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Shuffle arrangement of the ignition coils (among No. 1 to No. 6 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check DTCs displayed on the Techstream.

    Result:

    Display (DTC Output)
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)