Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1771    Passenger Side Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt RH.
DTC B1771 is recorded when a malfunction is detected in the passenger side buckle switch circuit.
Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are output simultaneously.

DTC Code
DTC Detection Condition
Trouble Area
B1771
One of following conditions is met:
  1. Occupant classification ECU detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in passenger side buckle switch circuit for 2 seconds
  2. Passenger side buckle switch malfunction
  3. Occupant classification ECU malfunction
  1. Front seat wire RH
  2. Front seat inner belt RH (Passenger side buckle switch)
  3. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1771 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.


WIRING DIAGRAM


E145805E01


INSPECTION PROCEDURE

NOTICE:
After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1771 is not output.

    HINT:
    Codes other than DTC B1771 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt RH.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK CONNECTOR
  1. Disconnect the connectors from the occupant classification ECU and the front seat inner belt RH.

  1. Check that the connectors (on the occupant classification ECU side and passenger side buckle switch side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH
E145672E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for Power Seat:
    Tester Connection
    Switch Condition
    Specified Condition
    Y2-9 (BSW) - Body ground
    Ignition switch ON
    Below 1 V
    Y2-5 (BGND) - Body ground
    for Manual Seat:
    Tester Connection
    Switch Condition
    Specified Condition
    Q11-9 (BSW) - Body ground
    Ignition switch ON
    Below 1 V
    Q11-5 (BGND) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (RBE+) and 2 (RBE-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for Power Seat:
    Tester Connection
    Condition
    Specified Condition
    Y2-9 (BSW) - Y2-5 (BGND)
    Always
    Below 1 Ω
    for Manual Seat:
    Tester Connection
    Condition
    Specified Condition
    Q11-9 (BSW) - Q11-5 (BGND)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for Power Seat:
    Tester Connection
    Condition
    Specified Condition
    Y2-9 (BSW) - Body ground
    Always
    1 MΩ or higher
    Y2-5 (BGND) - Body ground
    Y2-9 (BSW) - Y2-5 (BGND)
    for Manual Seat:
    Tester Connection
    Condition
    Specified Condition
    Q11-9 (BSW) - Body ground
    Always
    1 MΩ or higher
    Q11-5 (BGND) - Body ground
    Q11-9 (BSW) - Q11-5 (BGND)



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the front seat inner belt RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1771 is not output.

    HINT:
    Codes other than DTC B1771 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1771 is not output.

    HINT:
    Codes other than DTC B1771 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

END 

7.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU.

    1. for Power Seat (Click here)
    2. for Manual Seat (Click here)

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    If the DTCs are not cleared at this time, past DTCs will remain.


NEXT


8.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


9.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END