Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab)

AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E146445E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.

    Result: 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.*
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on (radio receiver, hazard switch, glove box, etc.).
    C
    Illumination comes on for all components except steering pad switch* and radio receiver.
    D

    HINT:
    *: For built-in type amplifier systems, there is no steering pad switch.



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)


    E121218E10
  1. Disconnect the J45 cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J45-12 (IL+2) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E145918E01

  1. Disconnect the z3 switch connector.

  1. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE


    C152441E06
  1. Disconnect the z3 switch connector.

  1. Disconnect the J45 cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - J45-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z3-5 (IL+2) - J45-12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the PRECAUTION for the SRS (Click here).



NG
REPLACE SPIRAL CABLE (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


    E145920E01
  1. Disconnect the K3 receiver connector.

  1. Disconnect the J45 cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K3-6 (SWG) - J45-4 (EAU)
    Always
    Below 1 Ω
    K3-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER)


    E145921E01
  1. Disconnect the K1*1 or K4*2 receiver connector.

    HINT:
    *1: for Built-in Type Amplifier System
    *2: for Separate Type Amplifier System

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for Separate Type Amplifier System:
    Tester Connection
    Switch Condition
    Specified Condition
    K4-2 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V
    for Built-in Type Amplifier System:
    Tester Connection
    Switch Condition
    Specified Condition
    K1-10 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMBINATION METER)


    E145922E01
  1. Disconnect the K2*1 or K4*2 receiver connector.

    HINT:
    *1: for Built-in Type Amplifier System
    *2: for Separate Type Amplifier System

  1. Disconnect the J28 meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for Separate Type Amplifier System:
    Tester Connection
    Condition
    Specified Condition
    K4-12 (ILL-) - J28-37 (ILL-)
    Always
    Below 1 Ω
    K4-12 (ILL-) - Body ground
    Always
    10 kΩ or higher
    for Built-in Type Amplifier System:
    Tester Connection
    Condition
    Specified Condition
    K2-5 (ILL-) - J28-37 (ILL-)
    Always
    Below 1 Ω
    K2-5 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)