DTC P0412 Secondary Air Injection System Switching Valve "A" Circuit |
DTC P0415 Secondary Air Injection System Switching Valve "B" Circuit |

| DTC Code | DTC Detection Condition | Trouble Area |
| P0412 P0415 |
|
|
| P0412 P0415 |
|
|
| Related DTCs | P0412: Secondary air injection system air switching valve circuit range check (bank 1) P0415: Secondary air injection system air switching valve circuit range check (bank 2) |
| Required Sensors/Components (Main) | Air injection control driver |
| Required Sensors/Components (Related) | Air switching valve |
| Frequency of Operation | Once per drive cycle |
| Duration | 3 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | - |
| Secondary air injection pump | Operating |
| Secondary air injection switching valve | Operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Time after ignition switch OFF to ON | 0.5 seconds or more |
| Starter | OFF |
| Time after starter turned from ON to OFF | 0.5 seconds or more |
| Monitor runs whenever following DTCs not present | - |
| Secondary air injection pump | Not operating |
| Secondary air injection switching valve | Not operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Time after ignition switch OFF to ON | 0.5 seconds or more |
| Starter | OFF |
| Time after starter turned from ON to OFF | 0.5 seconds or more |
| Diagnostic signal duty ratio from air injection control driver | 31% or more, and 48% or less |
| Diagnostic signal duty ratio from air injection control driver | 70% or more, and 90% or less when secondary air injection system operating. 0% when secondary air injection system not operating. |


| AID Diagnostic Signal Waveforms | ECM Commands | DTCs (ECM Output) | Suspected Trouble Area |
100% Duty Ratio![]() | Any Secondary Air Injection (AIR) System operation | P1613 P1614 |
|
0% Duty Ratio![]() | AIR System: ON (Air pump ON, ASV ON) | P1613 P1614 |
|
| AIR System: OFF (Air pump OFF, ASV OFF) | - | Normal | |
20% Duty Ratio![]() | Air Pump: ON | P0418 P0419 |
|
| Air Pump: OFF | P0418 P0419 |
| |
40% Duty Ratio![]() | ASV: ON | P0412 P0415 |
|
| ASV: OFF | P0412 P0415 |
| |
80% Duty Ratio![]() | AIR System: OFF (Air pump OFF, ASV OFF) | P1613 P1614 |
|
| AIR System: ON (Air pump ON, ASV ON) | - | Normal | |
| Other than above (other than 0, 20, 40, 80 and 100% duty) | - | P1613 P1614 |
|
| 1.INSPECT AIR SWITCHING VALVE ASSEMBLY |
![]() |
Disconnect the D58 or D59 air switching valve (ASV) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 5 (+B) - 1 (GND) | 20°C (68°F) | 4.5 to 5.5 Ω |
| 5 (+BL) - 1 (GNDL) | 20°C (68°F) | 4.5 to 5.5 Ω |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND) |
![]() |
Disconnect the D58 or D59 ASV connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D58-1 (GND) - Body ground | Always | Below 1 Ω |
| D59-1 (GNDL) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the D58 or D59 ASV connector.
Disconnect the D51 or D55 air injection control driver (AID) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D58-5 (+B) - D55-6 (VV) | Always | Below 1 Ω |
| D59-5 (+BL) - D51-6 (VV2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D58-5 (+B) or D55-6 (VV) - Body ground | Always | 1 kΩ or higher |
| D59-5 (+BL) or D51-6 (VV2) - Body ground | Always | 1 kΩ or higher |
|
| ||||
| OK | ||
| ||