Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P1613    Secondary Air Injection Driver Malfunction

DTC    P1614    Secondary Air Injection System Driver Bank 2

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC Code
DTC Detection Condition
Trouble Area
P1613
P1614
Either of following conditions (1) or (2) met:
(1) All of following conditions met (1 trip detection logic):
  1. Either of air pump or air switching valve not operating
  2. Diagnostic signal from Air Injection Control Driver (AID) 80%
  3. Battery voltage 8 V or more
(2) Both of following conditions met (1 trip detection logic):
  1. Battery voltage 8 V or more
  2. Diagnostic signal from AID abnormal (duty signal other than 0, 20, 40, 80 and 100%)
  1. Air injection control driver (AID)
  2. Open in AID ground circuit
P1613
P1614
  1. All of following conditions met (1 trip detection logic):
    1. Air injection system operating (Air Switching Valve [ASV] ON and air pump ON)
    2. Diagnostic signal from Air Injection Control Driver (AID) 0%
    3. Battery voltage 8 V or more
  1. Short in diagnostic information signal circuit (AID - ECM)
  2. Open or short in air pump and air switching valve command signal circuit (AID - ECM)
  3. Open in AID ground circuit
  4. AID
  5. ECM
P1613
P1614
  1. Both of following conditions met (1 trip detection logic):
    1. Battery voltage 8 V or more
    2. Diagnostic signal from Air Injection Control Driver (AID) 100%
  1. Open or short in AID power source circuit
  2. Open in diagnostic information signal circuit (AID - ECM)
  3. AID
  4. ECM

MONITOR DESCRIPTION

For a short time after cold engine starts, the ECM transmits command signals to the Air Injection Control Driver (AID) to drive the air pump and the Air Switching Valve (ASV). The AID detects open and short circuits according to the voltages at the AID terminals to the air pump and ASV, and the circuit voltage of the AID power source, and transmits diagnostic information as a signal to the ECM.
If the Secondary Air Injection (AIR) system circuit or the AID itself malfunctions, the AID sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM sets the DTC based on the diagnostic information from the AID.
EXAMPLE:
  1. The duty ratio of the diagnostic signal from the AID is 0 or 100% (remains at 0 V or the same as battery voltage).
  2. The duty ratio of the diagnostic signal from the AID shows an impossible ratio (other than 0, 20, 40, 80 and 100%).
  3. The AID outputs the normal signal (normal duty signal: 80%) while the system is not operating.

MONITOR STRATEGY


Related DTCs
P1613: Secondary air injection system air injection control driver circuit range check (bank 1)
P1614: Secondary air injection system air injection control driver circuit range check (bank 2)
Required Sensors/Components (Main)
Air injection control driver
Required Sensors/Components (Related)
Air switching valve
Frequency of Operation
Once per drive cycle
Duration
3 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1 and 4: 
Monitor runs whenever following DTCs not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

Case 2: 
Monitor runs whenever following DTCs not present
None
Either a or b met:
-
a. Air pump
Not operating
b. Air switching valve
Not operating
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

Case 3: 
Monitor runs whenever following DTCs not present
None
Following conditions (a) and (b) met
-
a. Air pump
Operating
b. Air switching valve
Operating
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Case 1: 
One of following conditions met:
A, B, C or D
A. Diagnostic signal duty ratio from air injection control driver
1% or more, and 10% or less
B. Diagnostic signal duty ratio from air injection control driver
30%
C. Diagnostic signal duty ratio from air injection control driver
49%
D. Diagnostic signal duty ratio from air injection control driver
91% or more, and 99% or less

Case 2: 
Diagnostic signal duty ratio from air injection control driver
70% or more, and 90% or less

Case 3: 
Diagnostic signal duty ratio from air injection control driver
0%

Case 4: 
Diagnostic signal duty ratio from air injection control driver
100%

COMPONENT OPERATING RANGE


Diagnostic signal duty ratio from air injection control driver
70% or more, and 90% or less when secondary air injection system operating.
0% when secondary air injection system not operating.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Diagnostic information output by the AID can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the AID. Reading the waveform while performing the AIR system intrusive operation provided in the System Check function, allows the possible trouble areas to be narrowed down.

NOTICE:
  1. This Air Injection Check*2 only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (Wait or Error).
    If an Error is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Air Injection Check*2 repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned ON or the engine running.
  4. Turn the ignition switch OFF when the Air Injection Check operation finishes.


AID Diagnostic Signal Waveform
ECM
Commands
DTCs
(ECM Output)
Suspected Trouble Area
100% Duty Ratio
A112066E01
Any Air Injection (AIR) System operation
P1613
P1614
  1. Open in diagnostic signal circuit
  2. Air Injection Control Driver (AID)
  3. Open in AID +B circuit (AID power source)
  4. Short between +B and diagnostic signal circuits
0% Duty Ratio
A112067E01
AIR System: ON (Air pump ON, ASV ON)
P1613
P1614
  1. Open or short in air pump or Air Switching Valve (ASV) command signal circuit (ECM - AID)
  2. Open in AID ground circuit
  3. Short between diagnostic signal circuit and body ground
  4. AID
  5. ECM
AIR System: OFF (Air pump OFF, ASV OFF)
-
Normal
20% Duty Ratio
A112068E01
Air Pump: ON
P0418
P0419
  1. Short between air pump drive circuit and body ground
  2. Harness and connector (AID - Pump)
  3. Air pump
  4. AID
  5. ECM
Air Pump: OFF
P0418
P0419
  1. Open in air pump drive circuit (AID - Pump), or short between air pump drive circuit and +B
  2. Harness and connector (AID - Pump)
  3. Air pump
  4. AID
  5. ECM
40% Duty Ratio
A112069E01
ASV: ON
P0412
P0415
  1. Short between ASV drive circuit and body ground
  2. Harness and connector (AID - ASV)
  3. ASV
  4. AID
  5. ECM
ASV: OFF
P0412
P0415
  1. Open in ASV drive circuit (AID - ASV), or short between ASV drive circuit and +B
  2. Harness and connector (AID - ASV)
  3. AID
  4. ASV
  5. ECM
80% Duty Ratio
A112070E01
AIR System: OFF (Air pump OFF, ASV OFF)
P1613
P1614
  1. AID
  2. ECM
AIR System: ON (Air pump ON, ASV ON)
-
Normal
Other than above
(other than 0, 20, 40, 80 and 100% duty)
-
P1613
P1614
  1. AID
  2. Open in AID ground circuit

HINT:
  1. By using the Techstream to perform the Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613 OR P1614)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P1613 and/or P1614
    A
    P1613 and/or P1614 and other DTCs
    B

    HINT:
    If any DTCs other than P1613 and P1614 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
A162286E03
  1. Disconnect the D51 or D55 air injection control driver (AID) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D55-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D51-5 (+B2) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (AID - ECM, BODY GROUND)
A162287E09
  1. Disconnect the A24 or D74 ECM connector.

  1. Disconnect the D55 or D51 AID connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D74-54 (AIRP) - D55-4 (SIP)
    Always
    Below 1 Ω
    D74-28 (AIRV) - D55-3 (SIV)
    Always
    Below 1 Ω
    D74-53 (ARP2) - D51-4 (SIP2)
    Always
    Below 1 Ω
    A24-43 (ARV2) - D51-3 (SIV2)
    Always
    Below 1 Ω
    D74-30 (AIDI) - D55-2 (DI)
    Always
    Below 1 Ω
    D74-29 (AID2) - D51-2 (DI2)
    Always
    Below 1 Ω
    D55-1 (E) - Body ground
    Always
    Below 1 Ω
    D51-1 (E2) - Body ground
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D74-54 (AIRP) or D55-4 (SIP) - Body ground
    Always
    10 kΩ or higher
    D74-28 (AIRV) or D55-3 (SIV) - Body ground
    Always
    10 kΩ or higher
    D74-53 (ARP2) or D51-4 (SIP2) - Body ground
    Always
    10 kΩ or higher
    A24-43 (ARV2) or D51-3 (SIV2) - Body ground
    Always
    10 kΩ or higher
    D74-30 (AIDI) or D55-2 (DI) - Body ground
    Always
    10 kΩ or higher
    D74-29 (AID2) or D51-2 (DI2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
A162286E04
  1. Disconnect the D55 or D51 AID connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D55-2 (DI) - D55-1 (E)
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D51-2 (DI2) - D51-1 (E2)
    Ignition switch ON
    11 to 14 V (near battery voltage)



NG
REPLACE ECM (Click here)
OK


5.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


6.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Start the engine and warm it up.

  1. Turn the ignition switch OFF.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Enter.

  1. After operating the AIR system, press the Enter button to confirm the AIR system pending codes.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    Other DTCs
    B

  1. Turn the ignition switch OFF.

    NOTICE:
    1. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch OFF when the Air Injection Check operation finishes.



B
GO TO DTC CHART (Click here)
A

END