Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor communication circuit consists of the occupant classification ECU and the center airbag sensor.
DTC B1790 is set when a malfunction is detected in the center airbag sensor communication circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1790
One of following conditions is met:
  1. Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in center airbag sensor communication circuit for 2 seconds
  2. Center airbag sensor malfunction
  3. Occupant classification ECU malfunction
  1. No. 2 floor wire
  2. Front seat wire RH
  3. Occupant classification ECU
  4. Center airbag sensor

HINT:
  1. When DTC B1630/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1790 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


C158891E02


INSPECTION PROCEDURE

NOTICE:
After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK CONNECTOR
  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.

    Result 
    Result
    Proceed tp
    Connectors are not deformed or damaged (for Power seat)
    A
    Connectors are not deformed or damaged (for Manual seat)
    B
    Connectors are deformed or damaged
    C



B
Go to step 11

C
REPLACE HARNESS OR CONNECTOR
A


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT
E146067E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Y2-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    Y2-4 (FSR-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y2-8 (FSR+) - Y2-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y2-8 (FSR+) - Y2-4 (FSR-)
    Always
    1 MΩ or higher
    Y2-8 (FSR+) - Body ground
    Y2-4 (FSR-) - Body ground



NG
Go to step 10
OK


5.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear any DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


7.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


8.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT


9.CHECK FOR DTC
  1. Connect the connector to the occupant classification ECU.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    DTC B1790 is not output
    A
    DTC B1790 is output (for Column Shift Type)
    B
    DTC B1790 is output (for Floor Shift Type)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

END 

10.CHECK FRONT SEAT WIRE RH
C193226E01
  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    QY1-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    QY1-9 (FSR-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the connector from the occupant classification ECU.

  1. Using a service wire, connect terminals 8 (FSR+) and 4 (FSR-) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    QY1-8 (FSR+) - QY1-9 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    QY1-8 (FSR+) - QY1-9 (FSR-)
    Always
    1 MΩ or higher
    QY1-8 (FSR+) - Body ground
    QY1-9 (FSR-) - Body ground



NG
REPLACE FRONT SEAT WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

11.CHECK NO. 2 FLOOR WIRE
E146808E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q11-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    Q11-4 (FSR-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q11-8 (FSR+) - Q11-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q11-8 (FSR+) - Q11-4 (FSR-)
    Always
    1 MΩ or higher
    Q11-8 (FSR+) - Body ground
    Q11-4 (FSR-) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK


12.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear any DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 13
OK

USE SIMULATION METHOD TO CHECK (Click here)  

13.REPLACE OCCUPANT DETECTION ECU
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


14.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


15.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT


16.CHECK FOR DTC
  1. Connect the connector to the occupant classification ECU.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    DTC B1790 is not output
    A
    DTC B1790 is output (for Column Shift Type)
    B
    DTC B1790 is output (for Floor Shift Type)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

END