Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for CrewMax)

DTC    01-DF    Master Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
01-DF*
When either condition below is met:
  1. Device with a display fails and master is switched to the audio device.
  2. Communication error between sub-master (stereo component amplifier) and master occurs.
  1. Navigation receiver power source circuit
  1. AVC-LAN circuit between navigation receiver and component which has stored this code
  1. AVC-LAN circuit between navigation receiver and stereo component amplifier
  1. Navigation receiver
  1. Component which has stored this code

HINT:
*: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch ON or ACC, this code is stored.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to erase codes stored due to the reasons described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The navigation receiver is the master unit.
  3. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read the DESCRIPTION before performing the following procedures.

1.CHECK NAVIGATION RECEIVER POWER SOURCE CIRCUIT
  1. Refer to the navigation receiver power source circuit (Click here).
    If the power source circuit is operating normally, proceed to the next step.


NEXT


2.INSPECT NAVIGATION RECEIVER
E145834E01
  1. Disconnect the K18 and K8 receiver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K18-5 (ATX+) - K18-15 (ATX-)
    Always
    60 to 80 Ω
    K8-9 (TXM+) - K8-10 (TXM-)*

    HINT:
    *: w/ Rear Seat Entertainment System

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER (Click here)

C
REPLACE NAVIGATION RECEIVER (Click here)
A


3.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


    E138069E01
  1. Enter the diagnostic mode.

  1. Press the "LAN Mon" switch to change to "LAN Monitor" mode.

  1. Identify the component which has stored this code.
    Component table 
    Display
    Component
    DSP-AMP
    Stereo component amplifier
    Rr-TV*
    Television display

    HINT:
    1. "DSP-AMP" is the component which has stored this code in the example shown in the illustration.
    2. *: w/ Rear Seat Entertainment System


NEXT


4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

HINT:
For details of the connectors, refer to "TERMINALS OF ECU" (Click here).



  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the navigation receiver and the component which has stored this code.

    1. Disconnect all connectors between the navigation receiver and the component which has stored this code.



    2. Check for an open or short in the AVC-LAN circuit between the navigation receiver and the component which has stored this code.

      OK:
      There is no open or short circuit.


      E138055E04


      E145835E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE NAVIGATION RECEIVER
  1. Replace the navigation receiver (for Column Shift Type) with a normal one (Click here).

  1. Replace the navigation receiver (for Floor Shift Type) with a normal one (Click here).

  1. Check if the same problem occurs again.

    OK:
    Same problem does not occur.



NG
REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK

END