Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 2UZ-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 2UZ-FE) > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER ASSEMBLY


C134407E06
  1. Using a vernier caliper and straightedge, measure dimension A between the transmission and the end surface of the drive plate.

  1. Install the torque converter to the transmission housing.



    C123813E02
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.

    Standard distance:
    A + 1 mm (0.0394 in.) or more



2. INSTALL TRANSMISSION CONTROL CABLE BRACKET


C155906
  1. Install the bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the front left bank bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the rear left bank bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



4. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


C157012E01
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil cooler spacer and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 hoses to the transmission oil cooler spacer with the 2 clips.



    C161815E01
  1. Install the transmission oil cooler with transmission oil cooler spacer with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 hoses with the 2 clips.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



5. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


C157011E01
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil thermostat and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 hoses to the transmission oil thermostat with 2 clips.



    C157009E01
  1. Install the transmission oil cooler with transmission oil thermostat with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 hoses with the 2 clips.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



6. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    C158372E01
  1. Install the transmission with the 10 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



7. CONNECT NO. 2 WATER BY-PASS PIPE (w/o Trailer Towing System)


C157031E01
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



    C161816
  1. Install the hose heat protector with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



8. CONNECT NO. 2 WATER BY-PASS PIPE (w/ Trailer Towing System)


C157030E01
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



    C155914
  1. Connect the 2 oil cooler hoses to the transmission oil cooler.



    C158375
  1. Install the hose heat protector with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



9. CONNECT WIRE HARNESS AND CONNECTOR


    C158369E02
  1. Connect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.

  1. Connect the harness clamp with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the 4 connector clamps and 4 harness clamps.

  1. Tilt up the automatic transmission.



    C155915
  1. Connect the ground cable with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



10. INSTALL REAR NO. 1ENGINE MOUNTING INSULATOR


C155909
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    40 N*m{ 407 kgf*cm , 30 ft.*lbf }



11. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C155908
  1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



    C155907
  1. Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts..

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



12. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


C155911
  1. Turn the crankshaft to gain access to the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then install the remaining 5 bolts.

  1. Install the flywheel housing under cover with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



13. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C158380E01
  1. Connect the control cable with a new clip and nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the inside of the vehicle.



14. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. for Regular Cab Standard Deck:
    Install the front exhaust pipe (Click here).

  1. except Regular Cab Standard Deck:
    Install the front exhaust pipe (Click here).



15. INSTALL PROPELLER SHAFT ASSEMBLY
  1. Install the propeller shaft (Click here).



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



17. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).



18. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A151850E04
  1. Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above. If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



19. CHECK FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



20. ADJUST SHIFT LEVER POSITION (for Column Shift Type)
  1. Move the shift lever to the N position.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



21. ADJUST SHIFT LEVER POSITION (for Floor Shift Type)
  1. Move the shift lever to the N position.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



22. INSPECT SHIFT LEVER POSITION (for Column Shift Type)
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



23. INSPECT SHIFT LEVER POSITION (for Floor Shift Type)
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



24. CHECK FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


25. INSTALL NO. 1 ENGINE UNDER COVER


26. RESET MEMORY
  1. Perform the RESET MEMORY procedures (A/T initialization) (Click here).