Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE NO. 1 ENGINE UNDER COVER


3. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151786E01

  1. Tighten the radiator drain cock plug by hand.



5. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft (Click here).



6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. for Regular Cab Standard Deck:
    Remove the front exhaust pipe (Click here).

  1. except Regular Cab Standard Deck:
    Remove the front exhaust pipe (Click here).



7. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C155905
  1. Remove the nut and clip, and disconnect the transmission control cable.



8. REMOVE STARTER ASSEMBLY (for 1.6 kW Type)
  1. Remove the terminal cap.



    A159478
  1. Remove the nut and disconnect the starter wire.

  1. Disconnect the starter connector.

  1. Remove the 2 bolts and starter.



9. REMOVE STARTER ASSEMBLY (for 2.0 kW Type)
  1. Remove the terminal cap.



    A159479
  1. Remove the nut and disconnect the starter wire.

  1. Disconnect the starter connector.

  1. Remove the 2 bolts and starter assembly.



10. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C157016
  1. Remove the flywheel housing side cover.



    C157017
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.



11. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C112848
  1. Support the transmission with a transmission jack.
    Lift the transmission slightly from the crossmember.



12. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C155908
  1. Remove the 4 bolts of the rear engine mounting insulator.



    C155907
  1. Remove the 4 nuts, 4 washers, 4 bolts and frame crossmember.



13. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


    C155909
  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.



14. DISCONNECT WIRE HARNESS AND CONNECTOR


C155915
  1. Remove the bolt and disconnect the ground cable.



    C112849
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



    C155912E01
  1. Disconnect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Disconnect the 4 connector clamps and 4 harness clamps.

  1. Remove the bolt and disconnect the harness clamp and wire harness.



15. DISCONNECT NO. 1 WATER BY-PASS PIPE


    C158364
  1. Remove the 2 bolts and disconnect the 2 water by-pass hoses from the transmission oil cooler, and separate the by-pass pipe from the automatic transmission.

    NOTICE:
    Use a container to catch any coolant which flows out of the water by-pass hoses.



16. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


C157018
  1. Remove the 9 bolts and transmission.

    NOTICE:
    Do not use excess force when prying the transmission assembly.



17. REMOVE TRANSMISSION OIL COOLER ASSEMBLY


C158367
  1. Disconnect the 2 oil cooler hoses.

  1. Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.



    C157012
  1. Remove the 3 bolts and separate the transmission oil cooler from the transmission oil cooler spacer.

  1. Remove the 2 O-rings.



18. REMOVE HARNESS CLAMP BRACKET
  1. Remove the 2 bolts and 2 brackets.



19. REMOVE TRANSMISSION CONTROL CABLE BRACKET


C155906
  1. Remove the 2 bolts and bracket.



20. REMOVE TORQUE CONVERTER ASSEMBLY


21. INSPECT TORQUE CONVERTER ASSEMBLY
  1. Inspect the torque converter clutch (Click here).