SFI SYSTEM > VC Output Circuit |




| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
|
| ||||
| OK | ||
| ||
| 2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and Techstream ON.
Check the communication between the Techstream and ECM.
| Result | Proceed to |
| Communication is possible | A |
| Communication is not possible | B |
|
| ||||
| B | |
| 3.CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the D9 throttle body connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the A14 accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 5.CHECK MIL (CANISTER PUMP MODULE) |
![]() |
Disconnect the R1 canister pump module connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 6.CHECK MIL (AIR SWITCHING VALVE for Bank 1) |
Disconnect the D58 air switching valve connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 7.CHECK MIL (AIR SWITCHING VALVE for Bank 2) |
Disconnect the D59 air switching valve connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR) |
Disconnect the D46 power steering oil pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 9.CHECK MIL (CAMSHAFT POSITION SENSOR) |
Disconnect the D6 camshaft position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 10.CHECK MIL (CRANKSHAFT POSITION SENSOR) |
Disconnect the D3 crankshaft position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 11.CHECK MIL (VVT SENSOR for Intake Side of Bank 1) |
Disconnect the D37 VVT sensor (for Intake Side of Bank 1) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 12.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 1) |
Disconnect the D40 VVT sensor (for Exhaust Side of Bank 1) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 13.CHECK MIL (VVT SENSOR for Intake Side of Bank 2) |
Disconnect the D39 VVT sensor (for Intake Side of Bank 2) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 14.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 2) |
Disconnect the D41 VVT sensor (for Exhaust Side of Bank 2) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
|
| ||||
| B | |
| 15.CHECK HARNESS AND CONNECTOR |
Disconnect the D9 throttle body connector.
Disconnect the A14 accelerator pedal position sensor connector.
Disconnect the R1 canister pump module connector.
Disconnect the D58 air switching valve connector.
Disconnect the D59 air switching valve connector.
Disconnect the D46 power steering oil pressure sensor connector.
Disconnect the D6 camshaft position sensor connector.
Disconnect the D3 crankshaft position sensor connector.
Disconnect the D37 VVT sensor (for Intake Side of Bank 1) connector.
Disconnect the D40 VVT sensor (for Exhaust Side of Bank 1) connector.
Disconnect the D39 VVT sensor (for Intake Side of Bank 2) connector.
Disconnect the D41 VVT sensor (for Exhaust Side of Bank 2) connector.
![]() |
Disconnect the A24 and D74 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-80 (VCTA) - Body ground | Always | 10 kΩ or higher |
| A24-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A24-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
| D74-66 (VCV2) - Body ground | Always | 10 kΩ or higher |
| D74-67 (VCV1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||