Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL PAD


    C155468
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


    C154462
  1. Install the brake pedal support with the 4 nuts.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

  1. Install the No. 3 brake pedal bracket to the brake pedal support.



    C154461
  1. Temporarily install the brake pedal support, No. 3 brake pedal bracket and brake pedal lever with the bolt and nut.



    C154460E03
  1. Install the bolt to the No. 3 brake pedal bracket.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal and return spring mounting bracket of the No. 3 brake pedal bracket.

  1. Install the brake pedal return spring.

  1. Tighten the bolt and nut.

    Torque:
    23 N*m{ 239 kgf*cm , 17 ft.*lbf }



3. INSTALL PUSH ROD PIN
  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

  1. Set the push rod clevis in place, insert the push rod pin from outside the vehicle and then install a new clip.

    NOTICE:
    After assembly, check that the pedal operates smoothly.



4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
  1. Install the stop light switch mounting adjuster .



5. INSTALL STOP LIGHT SWITCH ASSEMBLY
  1. Attach the harness clip.

  1. Install the stop light switch .

  1. Connect the stop light switch connector.



6. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    C154523
  1. Install the air duct with the bolt.



7. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT


    B160602
  1. Connect the connector.

  1. Attach the 2 claws to install the safety pad.

  1. Install the 4 bolts.



8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B160582
  1. Connect the connectors.

  1. Attach the 4 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



9. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



10. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Attach the 6 claws and 3 clips to install the scuff plate.



11. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Attach the 6 claws and 3 clips to install the scuff plate.



12. CHECK BRAKE PEDAL HEIGHT


    C154465E01
  1. Check the brake pedal height.

    Standard pedal height from dash panel:
    179.9 to 189.9 mm (7.08 to 7.48 in.)

    NOTICE:
    Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

    If the pedal height is incorrect, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket and dash panel.
    Even if there is damage, there is no problem if the reserve distance is within the standard value. If necessary, replace them.



13. CHECK PEDAL FREE PLAY


    C154467E01
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. Push in the brake pedal until the beginning of the resistance is felt. Measure the distance as shown in the illustration.

    Standard pedal free play:
    1.0 to 6.0 mm (0.0394 to 0.236 in.)



14. CHECK PEDAL RESERVE DISTANCE
  1. Release the parking brake pedal.



    R000934E23
  1. With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

    Standard pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):
    More than 104 mm (4.09 in.)

    If incorrect, troubleshoot the brake system (Click here).



15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



16. CHECK MASTER CYLINDER PRESSURE SENSOR SIGNAL
  1. Check the sensor signal (Click here).