Home › ENGINE ยท 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0607    Control Module Performance

for Preparation Click here


DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor (HO2S) transistors. This self-check ensures that the ECM is functioning properly.

DTC No.
DTC Detection Condition
Trouble Area
P0607
  1. ECM CPUs malfunction
  2. Heated oxygen sensor transistor (built into the ECM) malfunction
  1. ECM
  2. Heated oxygen sensor
  3. Exhaust gas leak

MONITOR STRATEGY


Related DTCs
None
Required sensors/Components (main)
ECM
Required sensors/Components (sub)
Heated oxygen sensor
Frequency of operation
Continuous
Duration
60 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not present
None
Engine
Running
Estimated heated oxygen sensor temperature
450 to 800°C (842 to 1472°F)

TYPICAL MALFUNCTION THRESHOLDS


Heated oxygen sensor transistors
Fail

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs (Click here).
    Result 
    Result
    Proceed to
    P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    A
    P0607 is output
    B



B
Go to step 3
A


2.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.

HINT:
  1. If P0136 or P0156 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
  2. If P0137 or P0157 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
  3. If P0138 or P0158 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
  4. If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).



NEXT
Go to step 6

3.CHECK FOR EXHAUST GAS LEAK
  1. Allow the engine to idle and rev the engine.

  1. Check for exhaust gas leaks around the heated oxygen sensor.
    If any exhaust gas leaks are present, repair it and proceed to "PERFORM CONFIRMATION DRIVING PATTERN". If no exhaust gas leaks are present proceed to "PERFORM CONFIRMATION DRIVING PATTERN".

    HINT:
    1. If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
    2. If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.


NEXT


4.PERFORM CONFIRMATION DRIVING PATTERN

A198852E01

  1. Connect the Techstream to the DLC3.

  1. Clear DTC (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  1. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  1. Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.

  1. Drive the vehicle at 32 km/h (20 mph) or more for 2 minutes.

  1. After this driving make sure that the Data List "Alcohol Density Learning" is "Compl".

  1. Perform the drive pattern.

    1. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.

    2. Drive the vehicle between 60 and 80 km/h (35 and 50 mph) for 5 minutes.

  1. Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0136, P0137, P0138, P0156, P0157, P0158 and/or P0607
    A
    Only P0607
    B
    No DTC output
    C



B
REPLACE ECM (Click here)

C
Go to step 6
A


5.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.

HINT:
  1. If P0136 or P0156 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
  2. If P0137 or P0157 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
  3. If P0138 or P0158 is output, troubleshoot for that DTC first (Click here). Then proceed to "INSPECT ECM".
  4. If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).


NEXT


6.INSPECT ECM
  1. Connect the Techstream to the DLC3.

  1. Clear DTC (Click here).

  1. Stop the engine and wait for 30 minutes.

  1. Start the engine and allow it to idle for 2 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check the DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    P0607 is output
    B



B
REPLACE ECM (Click here)
A

END