Home › ENGINE ยท 3UR-FBE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).
    2. After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



    A194647
  1. Disconnect the 2 fuel pump ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the 2 fuel pump ECU connectors.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



3. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A191562E01

  1. Tighten the radiator drain cock plug by hand.



5. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator (Click here).



6. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



7. REMOVE AIR CLEANER ASSEMBLY


    A162105E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. Unfasten the 4 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A156197E01
  1. Remove the 2 bolts and air cleaner case.



8. DISCONNECT ENGINE WIRE


  1. Engine Room LH Side:



      A162560
    1. Remove the engine room relay block cover.

    2. Disconnect the 2 connectors and detach the 2 clamps from the engine room junction block.



    3. A153551
    4. Disconnect the 4 air injection control driver connectors.



    5. A163944
    6. Disconnect the 2 wire harness clamps.



    7. A162561
    8. Disconnect the injector connector.

    9. Disconnect the 4 ignition coil connectors.

    10. Disconnect the 2 VVT sensor connectors.

    11. Disconnect the 4 clamps.

    12. Remove the 2 bolts and ground wire.

    13. Disconnect the noise filter connector.



    14. A162562
    15. Disconnect the engine coolant temperature sensor connector.

    16. Disconnect the 2 camshaft timing oil control valve connectors.

    17. Disconnect the camshaft position sensor connector.

    18. Disconnect the 3 clamps.

    19. Disconnect the cooler compressor connector.



    A162563
  1. Engine Room RH Side:

    1. Disconnect the 2 camshaft timing oil control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the injector connector.

    4. Disconnect the 2 VVT sensor connectors.

    5. Disconnect the noise filter connector.

    6. Remove the 2 bolts and ground wire.

    7. Disconnect the 2 air pump connectors.

    8. Disconnect the throttle position sensor and throttle control motor connector.

    9. Disconnect the 5 clamps.



    A162564E01
  1. Disconnect the 2 clamps and power steering oil pressure switch connector.

  1. Disconnect the clamp and junction connector.



9. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold (Click here).



10. DISCONNECT AIR PUMP HOSE AND WIRE HARNESS


    A163452E01
  1. Disconnect the No. 2 and No. 3 air hoses.

  1. Disconnect the 2 clamps.



11. DISCONNECT HEATER HOSE AND PIPE


    A163380
  1. Remove the 2 bolts and disconnect the 3 hoses.



12. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



13. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A165142E01
  1. Remove the 2 bolts and disconnect the fuel tube.



14. REMOVE OIL FILTER ELEMENT


    A094910E04
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.



    A162459
  1. Remove the oil filter drain plug.



    A162460E01
  1. Install the pipe to the oil filter cap.

    HINT:
    Use a container to catch the draining oil.

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.



    A162461
  1. Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.



    A178490E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A178458E01
  1. Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Be sure to remove the O-ring for the cap by hand, without using any tools, to prevent damage to the cap's O-ring groove.



15. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY


    A163657
  1. Disconnect the sender gauge connector.



    A162467
  1. Remove the oil pressure sender gauge.



16. REMOVE NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)


    A165547
  1. Remove the 3 bolts.

  1. Disconnect the 4 hoses and remove the water by-pass pipe.



17. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)


    A163672
  1. Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.



18. REMOVE OIL FILTER BRACKET (w/ Oil Cooler)


    A162469
  1. Remove the 2 bolts, 2 nuts and filter bracket.



    A162470
  1. Remove the 2 O-rings.



19. REMOVE OIL FILTER BRACKET (w/o Oil Cooler)


    A163541
  1. Remove the 2 bolts, 2 nuts and oil filter bracket.



    A162470
  1. Remove the 2 O-rings.



20. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



21. DISCONNECT VANE PUMP ASSEMBLY


    A163289
  1. Remove the 2 bolts and disconnect the vane pump.



22. REMOVE GENERATOR ASSEMBLY


    A163292
  1. Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.



    A163290
  1. Remove the bolt and disconnect the wire harness bracket from the generator.



    A163293
  1. Remove the 2 bolts, 2 nuts and generator.

  1. Remove the 2 stud bolts.



23. REMOVE NO. 1 WATER BY-PASS HOSE


    A162549
  1. Remove the No. 1 water by-pass hose by disconnect the hose from the water inlet housing and front water by-pass joint.



24. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A162550
  1. Remove the bolt and disconnect the air tube.



    A162551
  1. Disconnect the 2 hoses.

  1. Remove the 2 bolts and water by-pass pipe.



25. REMOVE FRONT WATER BY-PASS JOINT


    A162552
  1. Disconnect the No. 2 water by-pass hose from the water by-pass joint.

  1. Remove the 4 nuts, water by-pass joint and 2 gaskets.



26. REMOVE NO. 2 ENGINE COVER


A158576


27. REMOVE NO. 1 ENGINE COVER


A158581


28. REMOVE AIR TUBE SUB-ASSEMBLY


    A162553
  1. Remove the bolt, disconnect the 2 hoses, and remove the air tube.



29. REMOVE WATER INLET HOUSING


    A162554
  1. Remove the 3 bolts, water inlet housing and gasket.



30. REMOVE WATER PUMP PULLEY


    A162556E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



31. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Remove the bolt and idler pulley.



32. REMOVE FAN BRACKET ASSEMBLY


    A162558
  1. Remove the 4 bolts and fan bracket.



33. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A162527
  1. Remove the standard bolt, 6 mm hexagon bolt and belt tensioner.



34. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 8 bolts and 8 ignition coils.



35. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162523
  1. Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A162524
  1. Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).



36. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A163381
  1. Remove the bolt and noise filter.



    A162525
  1. Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A162526
  1. Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).



37. REMOVE CRANKSHAFT PULLEY


    A164228E01
  1. Using SST, loosen the crankshaft pulley set bolt.

    SST
    09213-70011  
    09330-00021  

  1. Partially install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.



    A164229E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)



38. DISCONNECT WIRE HARNESS CLAMP BRACKET


    A163733
  1. Remove the bolt and disconnect the bracket.



39. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A162529E01
  1. Remove the 28 bolts and nut shown in the illustration.



    A162530
  1. Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the cylinder head and cylinder block contact surfaces of the chain cover.



    A162531
  1. Remove the oil pump gasket from the cylinder block.



    A164415
  1. Remove the O-ring from the oil pan.



40. REMOVE WATER INLET PIPE


    A162532
  1. Remove the water inlet pipe.

  1. Remove the 2 O-rings from the water inlet pipe.