Home › BODY › INTERIOR › ROOF HEADLINING (for Regular Cab)

ROOF HEADLINING (for Regular Cab) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Remove the front seat (Click here).



3. REMOVE FRONT SEAT ASSEMBLY (for Fold Down Seat Type)
  1. Remove the front seat (Click here).



4. REMOVE FRONT SEAT ASSEMBLY (for Center Seat)
  1. Remove the front seat (Click here).



5. REMOVE FRONT DOOR SCUFF PLATE LH


B165843
  1. Detach the 6 claws and 3 clips, and remove the scuff plate.



6. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



7. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



8. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


11. REMOVE UPPER BACK PANEL GARNISH


B164740
  1. Detach the 10 clips and remove the back panel garnish.



12. REMOVE LUGGAGE COMPARTMENT BOX LH


B164747
  1. Remove the 2 clips.

  1. Detach the 3 claws and remove the luggage compartment box.



13. REMOVE LUGGAGE COMPARTMENT BOX RH


B164748
  1. Remove the 4 clips and luggage compartment box.



14. REMOVE FRONT PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B165705E03



    B165709E01
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



15. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



16. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH


B165729
  1. Detach the 2 claws and remove the cover.



    B165728
  1. Remove the bolt and outer lap belt anchor.



    B165710
  1. Detach the 7 clips and remove the quarter trim panel.



17. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH


B164750
  1. Detach the 2 claws and remove the cover.



    B164749
  1. Remove the bolt and outer lap belt anchor.



    B164745
  1. Detach the 8 clips and remove the quarter trim panel.



18. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH


B165711E01
  1. Using a screwdriver, detach the claw and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



    B165727
  1. Detach the 2 claws and open the seat belt anchor cover.



    B165726
  1. Remove the bolt and disconnect the seat belt's shoulder anchor.



    B165725
  1. Remove the 2 bolts.

  1. Detach the 5 clips and remove the quarter trim panel.



19. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



20. REMOVE ROOF CONSOLE BOX ASSEMBLY
  1. Remove the 4 screws.



  1. Disconnect the connector and then remove the roof console box.


    B167127E01



21. REMOVE VISOR BRACKET COVER LH


B165714
  1. Using a moulding remover, detach the 4 claws and remove the visor bracket cover.



22. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



23. REMOVE VISOR ASSEMBLY LH


B165715
  1. Remove the 3 screws and visor.



24. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



25. REMOVE VISOR HOLDER


B165713
  1. Remove the screw and visor holder.

    HINT:
    Use the same procedure to remove the visor holder on the other side.



26. REMOVE ASSIST GRIP SUB-ASSEMBLY


B155751E05
  1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the 2 clips and remove the assist grip.



27. REMOVE ASSIST GRIP PLUG


B165716E04
  1. Insert a screwdriver into the service notch and break off the cap.

  1. Detach the clip and remove the assist grip plug.



28. REMOVE COAT HOOK


B165718E01
  1. Using a screwdriver, detach the 2 claws and remove the coat hook cap.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the screw and coat hook.



29. REMOVE ROOF HEADLINING ASSEMBLY


  1. w/ EC Mirror:



      B166355
    1. Detach the 2 claws and remove the inner rear view mirror cover.



    2. B167283
    3. Disconnect the EC mirror connector.



    B165722
  1. Disconnect the roof wire connector and detach each clamp from the front pillar.



    B165724
  1. Detach the 3 clips.



    B165844
  1. Take out the roof headlining from the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when taking it out.