Home › ENGINE ยท 2UZ-FE › ENGINE MECHANICAL › CAMSHAFT (for Bank 1)

CAMSHAFT (for Bank 1) > REMOVAL

for Preparation Click here



1. REMOVE TIMING BELT
  1. Remove the timing belt (Click here).



2. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 1)
  1. Remove the air switching valve (Click here).



3. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 4 ignition coil connector.

  1. Remove the 4 bolts and 4 ignition coils.



4. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A160762
  1. Remove the 9 bolts, cylinder head cover and gasket.



5. REMOVE CAMSHAFT POSITION SENSOR ASSEMBLY


    A134807
  1. Remove the bolt, stud bolt and camshaft position sensor.



6. REMOVE CAMSHAFT TIMING PULLEY LH


    A160789
  1. Hold the hexagonal portion of the camshaft with a wrench and remove the 4 bolts indicated by the arrows in the illustration and timing pulley.

    NOTICE:
    1. Do not loosen or remove the 4 bolts that are not indicated by the arrows in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the timing tube assembly with a new one.
    2. Be careful not to damage the cylinder head with the wrench.



7. REMOVE CAMSHAFT SUB-ASSEMBLY LH

NOTICE:
  1. As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged. To avoid this, the following steps should be carried out.

  2. A134393E04
    Having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft. Always set the crankshaft pulley at the correct angle as shown in the illustration.



    A118100E01
  1. Bring the service bolt hole of the sub-gear upward by turning the hexagonal portion of the exhaust camshaft with a wrench.

  1. Secure the sub-gear to the main gear with a service bolt.

    Recommended service bolt:
    Thread Diameter
    Thread Pitch
    Bolt Length
    6.0 mm
    1.0 mm
    16 to 20 mm (0.630 to 0.787 in.)

    HINT:
    When removing the camshafts, make sure that the torsional spring force of the sub-gear has been eliminated by the above operation.



    A118105
  1. Using a wrench, turn the camshaft so that the timing marks (2 dot marks each) on the camshaft drive and driven main gears are aligned, as shown in the illustration.



    A118099E01
  1. Uniformly loosen and remove the 22 bearing cap bolts in several steps, in the order shown in the illustration.



    A160810
  1. Remove the cap bolts, 4 seal washers, oil feed pipe, 9 bearing caps, camshaft housing plug, oil control valve filter and camshafts.

    NOTICE:
    1. Do not forcibly pry the camshaft with a tool.
    2. Do not damage the reception part of the thrust on the cylinder head side.

    HINT:
    Arrange the bearing caps in the correct order.



8. REMOVE CAMSHAFT TIMING TUBE ASSEMBLY


    A118101E02
  1. Mount the hexagonal portion of the camshaft in a vise.

    NOTICE:
    1. Be careful not to damage the camshaft.
    2. Do not loosen or remove the 4 bolts shown in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the timing tube assembly with a new one.

  1. Remove the screw plug and seal washer.



    A118091E01
  1. Using a 10 mm hexagon wrench, remove the bolt.

  1. Pull out the timing tube and drive gear assembly from the camshaft.



    A054029E03
  1. Using SST and a 5 mm hexagon wrench, remove the 4 bolts, drive gear and oil seal.

    SST
    09960-10010   (09963-00500)

    NOTICE:
    Be careful not to damage the timing tube.



9. REMOVE CAMSHAFT SUB-GEAR


    A054968E01
  1. Mount the hexagonal portion of the camshaft in a vise.

    NOTICE:
    Be careful not to damage the camshaft.



    A054969E02
  1. Using SST, turn the sub-gear clockwise, and remove the service bolt.

    SST
    09960-10010   (09963-00500)

  1. Using snap ring pliers, remove the snap ring.

  1. Remove the wave washer, sub-gear and gear spring.

    HINT:
    Arrange the camshaft sub gears and gear spring (LH and RH).