Home › RESTRAINTS › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

The meter ECU detects the state of the front seat inner belt RH when the front passenger side seat is occupied with the ignition switch ON. If the front passenger side seat belt is not fastened, the front passenger side seat belt warning light on the integration control and panel blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM


B165402E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Check for DTCs.

    1. for CAN communication system (Click here).

    2. for Airbag system (Click here).

    3. for Occupant classification system (Click here).
      Result: 
      Result
      Proceed to
      DTC is not output
      A
      CAN communication system DTC is output
      B
      Airbag system DTC is output
      C
      Occupant classification system DTC is output
      D



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO AIRBAG SYSTEM (Click here)

D
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
A


2.INSPECT FUSE (ECU-IG No. 1)
  1. Remove the ECU-IG No. 1 fuse from the passenger side junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT PASSENGER SEAT BELT WARNING LIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Combination Meter: 
    Item
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp P-seat Belt
    Front passenger side seat belt warning light
    ON or OFF
    -



OK
Go to step 6
NG


4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - COMBINATION METER AND BATTERY)
B167471E01
  1. Disconnect the J37 panel connector.

  1. Disconnect the J28 meter connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J37-14 (PBEW) - J28-15 (P/SB)
    Always
    Below 1 Ω
    J37-14 (PBEW) - Body ground
    Always
    10 kΩ or higher
    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J37-16 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY
B165622E01
  1. Remove the integration control and panel (Click here).

  1. Connect the positive (+) battery lead to terminal 16 (IG+), and the negative (-) battery lead to terminal 14 (PBEW).

  1. Check that the front passenger side seat belt warning light comes on.

    OK:
    Front passenger side seat belt warning light (for passenger side) comes on.



NG
REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER (Click here)  

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Temporarily replace the front seat inner belt RH with a new or normally functioning one (Click here).


NEXT


7.CHECK FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT
  1. Check the front passenger side seat belt warning light function (Click here).

    OK:
    Front passenger side seat belt warning light operates normally.



NG
REPLACE COMBINATION METER (Click here)
OK

END (FRONT SEAT INNER BELT RH IS DEFECTIVE)