SFI SYSTEM > Fuel Pump Control Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether operating sounds can be heard while operating the fuel pump using the Techstream.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND) |
![]() |
Disconnect the R7 fuel pump ECU connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R7-1 (FPC) - A24-52 (FPC) | Always | Below 1 Ω |
| R7-2 (DI) - A24-18 (DI) | Always | Below 1 Ω |
| R7-3 (E) - Body ground | Always | Below 1 Ω |
| R7-1 (FPC) or A24-52 (FPC) - Body ground | Always | 10 kΩ or higher |
| R7-2 (DI) or A24-18 (DI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here)
| NEXT | |
| 4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 5.INSPECT CIRCUIT OPENING RELAY (C/OPN) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Standard resistance | Condition | Specified Condition |
| 3 - 5 | When no battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C/OPN relay (2) - Body ground | Ignition switch ON | 11 to 14 V |
| C/OPN relay (5) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM AND FUEL PUMP ECU) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Disconnect the A24 ECM connector.
Disconnect the R7 fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPN relay (1) - A24-48 (FC) | Always | Below 1 Ω |
| C/OPN relay (3) - R7-4 (+B) | Always | Below 1 Ω |
| C/OPN relay (1) or A24-48 (FC) - Body ground | Always | 10 kΩ or higher |
| C/OPN relay (3) or R7-4 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU) |
![]() |
Disconnect the R6 fuel pump connector.
Disconnect the R8 fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R6-4 (B2) - R8-1 (FP) | Always | Below 1 Ω |
| R6-5 (E2) - R8-2 (FP-) | Always | Below 1 Ω |
| R6-4 (B2) or R8-1 (FP) - Body ground | Always | 10 kΩ or higher |
| R6-5 (E2) or R8-2 (FP-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND) |
![]() |
Disconnect the R7 fuel pump ECU connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R7-1 (FPC) - A24-52 (FPC) | Always | Below 1 Ω |
| R7-2 (DI) - A24-18 (DI) | Always | Below 1 Ω |
| R7-3 (E) - Body ground | Always | Below 1 Ω |
| R7-1 (FPC) or A24-52 (FPC) - Body ground | Always | 10 kΩ or higher |
| R7-2 (DI) or A24-18 (DI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here)
| NEXT | |
| 12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - IGN FUSE AND INTEGRATION RELAY) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block.
Remove the IGN fuse from the engine room relay block.
Remove the integration relay from the engine room relay block.
Disconnect the 1B integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPN relay (2) - IGN fuse (2) | Always | Below 1 Ω |
| C/OPN relay (5) - 1B-4 | Always | Below 1 Ω |
| C/OPN relay (2) or IGN fuse (2) - Body ground | Always | 10 kΩ or higher |
| C/OPN relay (5) or 1B-4 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||