SLIDING ROOF SYSTEM > Sliding Roof Control Switch Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (SLIDING ROOF OPERATION) |
Select the Active Test, use the Techstream to generate a control command, and then check that the sliding roof operates (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Slide Roof | Operate sliding roof SLIDE CLOSE/TILT UP or SLIDE OPEN/TILT DOWN | CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs OPN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs OFF: Sliding roof is not operating | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (SLIDING ROOF SWITCH) |
Use the Data List to check if the sliding roof switch is functioning properly (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Open Switch | Sliding roof open switch signal/ON or OFF | ON: SLIDE switch is pressed to open OFF: SLIDE switch is not pressed to open | - |
| Close Switch | Sliding roof close switch signal/ON or OFF | ON: SLIDE switch is pressed to close OFF: SLIDE switch is not pressed to close | - |
| Up Switch | Sliding roof up switch signal/ON or OFF | ON: TILT switch is pressed to up OFF: TILT switch is not pressed to up | - |
| Down Switch | Sliding roof down switch signal/ON or OFF | ON: TILT switch is pressed to down OFF: TILT switch is not pressed to down | - |
|
| ||||
| OK | ||
| ||
| 3.INSPECT SLIDING ROOF SWITCH |
![]() |
Remove the sliding roof switch .
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (UP) - 5 (E) | TILT switch is pressed to up | Below 1 Ω |
| 1 (UP) - 5 (E) | TILT switch is not pressed to up | 10 kΩ or higher |
| 2 (DWN) - 5 (E) | TILT switch is pressed to down | Below 1 Ω |
| 2 (DWN) - 5 (E) | TILT switch is not pressed to down | 10 kΩ or higher |
| 4 (OPN) - 5 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| 4 (OPN) - 5 (E) | SLIDE switch is not pressed to open | 10 kΩ or higher |
| 3 (CLS) - 5 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| 3 (CLS) - 5 (E) | SLIDE switch is not pressed to close | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT ROOF CONSOLE BOX ASSEMBLY |
![]() |
Remove the roof console box with sliding roof switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (UP) - 7 (E) | TILT switch is pressed to up | Below 1 Ω |
| 6 (UP) - 7 (E) | TILT switch is not pressed to up | 10 kΩ or higher |
| 5 (DWN) - 7 (E) | TILT switch is pressed to down | Below 1 Ω |
| 5 (DWN) - 7 (E) | TILT switch is not pressed to down | 10 kΩ or higher |
| 4 (OPN) - 7 (E) | SLIDE switch is pressed to open | Below 1 Ω |
| 4 (OPN) - 7 (E) | SLIDE switch is not pressed to open | 10 kΩ or higher |
| 3 (CLS) - 7 (E) | SLIDE switch is pressed to close | Below 1 Ω |
| 3 (CLS) - 7 (E) | SLIDE switch is not pressed to close | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX) |
![]() |
Disconnect the W3 ECU connector.
Disconnect the W7 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W3-1 (UP) - W7-6 (UP) | Always | Below 1 Ω |
| W3-2 (DWN) - W7-5 (DWN) | Always | Below 1 Ω |
| W3-6 (OPN) - W7-4 (OPN) | Always | Below 1 Ω |
| W3-7 (CLS) - W7-3 (CLS) | Always | Below 1 Ω |
| W7-6 (UP) - Body ground | Always | 10 kΩ or higher |
| W7-5 (DWN) - Body ground | Always | 10 kΩ or higher |
| W7-3 (CLS) - Body ground | Always | 10 kΩ or higher |
| W7-4 (OPN) - Body ground | Always | 10 kΩ or higher |
| W7-7 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||