Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A164725E01


INSPECTION PROCEDURE

1.CHECK INJECTOR ASSEMBLY (POWER SOURCE)
A182504E02
  1. Disconnect the fuel injector connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    D11-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 2
    D26-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 3
    D13-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 4
    D24-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 5
    D15-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 6
    D22-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 7
    D17-1 - Ground
    Ignition switch ON
    11 to 14 V
    No. 8
    D20-1 - Ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 6
OK


2.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
A181795E03
  1. Disconnect the fuel injector connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    D11-2 - Body ground
    Always
    10 kΩ or higher
    D11-2 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    D26-2 - Body ground
    Always
    10 kΩ or higher
    D26-2 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    D13-2 - Body ground
    Always
    10 kΩ or higher
    D13-2 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    D24-2 - Body ground
    Always
    10 kΩ or higher
    D24-2 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    D15-2 - Body ground
    Always
    10 kΩ or higher
    D15-2 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    D22-2 - Body ground
    Always
    10 kΩ or higher
    D22-2 - D74-107 (#60)
    Always
    Below 1 Ω
    No. 7
    D17-2 - Body ground
    Always
    10 kΩ or higher
    D17-2 - D74-83 (#70)
    Always
    Below 1 Ω
    No. 8
    D20-2 - Body ground
    Always
    10 kΩ or higher
    D20-2 - D74-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5.CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.
    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A

END 

6.INSPECT FUSE (INJ)
A181865E01
  1. Remove the INJ fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


7.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - INTEGRATION RELAY)
A181796E02
  1. Disconnect the fuel injector connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - 1B-8
    Always
    Below 1 Ω
    No. 2
    C16-2 - Body ground
    Always
    10 kΩ or higher
    C16-2 - 1B-8
    Always
    Below 1 Ω
    No. 3
    C7-2 - Body ground
    Always
    10 kΩ or higher
    C7-2 - 1B-8
    Always
    Below 1 Ω
    No. 4
    C14-2 - Body ground
    Always
    10 kΩ or higher
    C14-2 - 1B-8
    Always
    Below 1 Ω
    No. 5
    C9-2 - Body ground
    Always
    10 kΩ or higher
    C9-2 - 1B-8
    Always
    Below 1 Ω
    No. 6
    C12-2 - Body ground
    Always
    10 kΩ or higher
    C12-2 - 1B-8
    Always
    Below 1 Ω
    No. 7
    C25-2 - Body ground
    Always
    10 kΩ or higher
    C25-2 - 1B-8
    Always
    Below 1 Ω
    No. 8
    C54-2 - Body ground
    Always
    10 kΩ or higher
    C54-2 - 1B-8
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECU POWER SOURCE CIRCUIT (Click here)