Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the front catalyst to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the Oxygen Storage Capacity (OSC) of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air-fuel ratio control.
The OSC value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the heated oxygen sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the heated oxygen sensor and three-way catalytic converter.
The ECM uses the OSC value to determine the state of the three-way catalytic converter. If any deterioration has occurred, it illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0420
OSC value is less than the standard value under active air-fuel ratio control (1 trip detection logic)
  1. Gas leakage from exhaust system
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. Heated oxygen sensor (bank 1 sensor 2)
  4. Front exhaust pipe assembly (TWC: Front catalyst and Rear catalyst)
P0430
OSC value is less than the standard value under active air-fuel ratio control (1 trip detection logic)
  1. Gas leakage from exhaust system
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. Heated oxygen sensor (bank 2 sensor 2)
  4. Front No. 2 exhaust pipe assembly (TWC: Front catalyst and Rear catalyst)

CATALYST LOCATION


A245727E01


Text in Illustration 
*A
for Regular Cab Standard Deck
*B
except Regular Cab Standard Deck
*1
Exhaust Manifold Sub-assembly RH
*2
Exhaust Manifold Sub-assembly LH
*3
Front Exhaust Pipe Assembly (TWC: Front catalyst and Rear catalyst)
*4
Front No. 2 Exhaust Pipe Assembly (TWC: Front catalyst and Rear catalyst)
*5
Center Exhaust Pipe Assembly
*6
Tailpipe Assembly
*7
Air Fuel Ratio Sensor (for Bank 1 Sensor 1)
*8
Air Fuel Ratio Sensor (for Bank 2 Sensor 1)
*9
Heated Oxygen Sensor (for Bank 1 Sensor 2)
*10
Heated Oxygen Sensor (for Bank 2 Sensor 2)

MONITOR STRATEGY


Related DTCs
P0420: Catalyst Deterioration (bank 1)
P0430: Catalyst Deterioration (bank 2)
Required Sensors/Components (Main)
Air fuel ratio sensor and heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
About 30 seconds
MIL Operation
1 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058, P102D, P105D (Rear Oxygen Sensor Heater)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air Fuel Ratio Sensor)
P0136, P0137, P0138, P0139, P0156, P0157, P0158, P0159, P0607 (Rear Oxygen Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle Speed Sensor)
P0412, P0418, P1613 (Secondary Air Injection System Control)
P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary Air Injection System)
P219A, P219B (Air-fuel ratio imbalance)
Battery voltage
11 V or higher
Intake air temperature
-10°C (14°F) or higher
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa (570 mmHg) or higher
Idling
OFF
Engine speed
Less than 3200 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Engine load
10 to 80%
All of following conditions (a), (b) and (c) met
-
(a) Mass airflow
5 to 70 gm/s
(b) Estimated front catalyst temperature
560 to 840°C (1040 to 1544°F)
(c) Estimated rear catalyst temperature
100 to 900°C (212 to 1652°F)
Gear
4th or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of catalyst (Normalized)
Less than 1

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
  1. It is necessary that the response of the heated oxygen sensor is normal in order to confirm DTC P0420. Therefore, perform the driving pattern for the heated oxygen sensor monitor before performing the drive pattern for the catalyst efficiency monitor.
  2. Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283604E06

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  11. With the shift lever in the S position, drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].
  13. Check the Test Value for RL F/C B1S2, RL F/C B2S2.
    1. If Test Value displays a value larger than 0, perform the following procedure, as the O2 sensor monitor is finished.

      HINT:
      If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.

  14. Turn the ignition switch off and wait for at least 30 seconds [F].
  15. Turn the ignition switch to ON and turn the Techstream on.
  16. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].
  17. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates [I].

  18. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  19. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, perform the following procedure.

  20. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [J].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates [K].

  21. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  22. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, extend the driving time.

  23. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is in order to activate the sensors sufficiently to obtain appropriate inspection results.


A118003E64

  1. Connect the Techstream to the DLC3 (a).
  2. Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes (b).
  3. Run the engine at an engine speed between 2500 rpm and 3000 rpm for at least 3 minutes (c).
  4. While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the Techstream (d).

HINT:
  1. If the voltage output of the air fuel ratio sensor or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor which has those problems may be malfunctioning.
  2. If the voltage outputs of both sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the Techstream.
  3. If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).


A121610E50


INSPECTION PROCEDURE

HINT:
  1. If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 or P0174 (System Too Lean) and P0172 or P0175 (System Too Rich).
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Sensor 1 refers to the sensor closest to the engine assembly.
  6. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0420 or P0430 is output
    A
    P0420 or P0430 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Turn the Techstream on.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of -12.5% to +12.5%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    +12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    +12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS Voltage B1S1
    Status
    O2S B1S2
    Actual air fuel ratio, air fuel ratio sensor and
    heated oxygen sensor condition
    Misfire
    Main Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leak from exhaust system
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leak from exhaust system
    D
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leak from exhaust system
    Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1 or AFS Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2 or O2S B2S2) is consistently below 0.4 V.
    Rich: During Control the Injection Volume, the AFS Voltage B1S1 or AFS Voltage B2S1 is consistently below 3.1 V, and the O2S B1S2 or O2S B2S2 is consistently higher than 0.55 V.
    Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate



B
Go to step 5

C
Go to step 6

D
Go to step 8
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When DTC P0420 is output, replace the front exhaust pipe assembly (TWC: Front catalyst and Rear catalyst) together when catalyst replacement is necessary.
  2. When DTC P0430 is output, replace the No. 2 exhaust pipe assembly (TWC: Front catalyst and Rear catalyst) together when catalyst replacement is necessary.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0420 (for Regular Cab Standard Deck)
    A
    P0430 (for Regular Cab Standard Deck)
    B
    P0420 and P0430 (for Regular Cab Standard Deck)
    A and B
    P0420 (except Regular Cab Standard Deck)
    C
    P0430 (except Regular Cab Standard Deck)
    D
    P0420 and P0430 (except Regular Cab Standard Deck)
    C and D



B
REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)

C
REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)

D
REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)
A

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)  

5.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NEXT
Go to step 10

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


7.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the heated oxygen sensor (Click here).



NEXT
Go to step 10

8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (Click here).


NEXT


10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 or P0430 is output
    A
    DTC is not output
    B



B
END
A


11.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When DTC P0420 is output, replace the front exhaust pipe assembly (TWC: Front catalyst and Rear catalyst) together when catalyst replacement is necessary.
  2. When DTC P0430 is output, replace the No. 2 exhaust pipe assembly (TWC: Front catalyst and Rear catalyst) together when catalyst replacement is necessary.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0420 (for Regular Cab Standard Deck)
    A
    P0430 (for Regular Cab Standard Deck)
    B
    P0420 and P0430 (for Regular Cab Standard Deck)
    A and B
    P0420 (except Regular Cab Standard Deck)
    C
    P0430 (except Regular Cab Standard Deck)
    D
    P0420 and P0430 (except Regular Cab Standard Deck)
    C and D



B
REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)

C
REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)

D
REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)
A

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) (Click here)