DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
DTC P0174 System Too Lean (Bank 2) |
DTC P0175 System Too Rich (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0171 P0174 | With a warm engine and stable air-fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). |
|
| P0172 P0175 | With a warm engine and stable air-fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). |
|

| Related DTCs | P0171: Fuel trim lean (for Bank 1) P0172: Fuel trim rich (for Bank 1) P0174: Fuel trim lean (for Bank 2) P0175: Fuel trim rich (for Bank 2) |
| Required Sensors/Components | Air fuel ratio sensor, Mass air flow meter, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Within 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0412, P0418, P1613 (Secondary air injection system control) P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary air injection system) P0500 (Vehicle speed sensor) P219A, P219B (Air-fuel ratio imbalance) |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or higher |
| Either of following conditions 1 or 2 met | - |
| 1. Engine speed | Less than 1100 rpm |
| 2. Engine load | 10% or more |
| Catalyst monitor | Not executed |
| Purge-cut | Executing |
| Either of following conditions 1 or 2 met | - |
| 1. Average of short-term fuel trim and long-term fuel trim | 35% or more (varies with engine coolant temperature) |
| 2. Average of short-term fuel trim and long-term fuel trim | -35% or less (varies with engine coolant temperature) |

| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0171, P0172, P0174 or P0175 is output | A |
| P0171, P0172, P0174 or P0175 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage .
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | +12.5% | Rich | Below 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | +12.5% | Rich | Higher than 0.55 V |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | -12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - | A |
| Lean | Lean | Actual air fuel ratio lean |
| A |
| Rich | Rich | Actual air fuel ratio rich |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
|
| ||||
| A | |
| 5.READ VALUE USING TECHSTREAM (COOLANT TEMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 9.CHECK FOR SPARKS AND IGNITION |
Perform a spark test .
| NEXT | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Check the injection volume and volume .
|
| ||||
|
| ||||
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D33-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D34-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for Bank 1 Sensor 1 |
| *B | for Bank 2 Sensor 1 |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D33-1 (HA1A) - D74-22 (HA1A) | Always | Below 1 Ω |
| D33-3 (A1A+) - D74-126 (A1A+) | Always | Below 1 Ω |
| D33-4 (A1A-) - D74-125 (A1A-) | Always | Below 1 Ω |
| D34-1 (HA2A) - D74-20 (HA2A) | Always | Below 1 Ω |
| D34-3 (A2A+) - D74-103 (A2A+) | Always | Below 1 Ω |
| D34-4 (A2A-) - D74-102 (A2A-) | Always | Below 1 Ω |
| D33-1 (HA1A) or D74-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D33-3 (A1A+) or D74-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D33-4 (A1A-) or D74-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| D34-1 (HA2A) or D74-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| D34-3 (A2A+) or D74-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| D34-4 (A2A-) or D74-102 (A2A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0171, P0172, P0174 or P0175 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0171, P0172, P0174 or P0175 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D7-5 (VG) - D74-74 (VG) | Always | Below 1 Ω |
| D7-4 (E2G) - D74-75 (E2G) | Always | Below 1 Ω |
| D7-5 (VG) or D74-74 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 19.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| No DTC is output | A |
| DTC P0171, P0172, P0174 or P0175 is output | B |
|
| ||||
| A | ||
| ||
| 21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY) |
Disconnect the air fuel ratio sensor connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D33-2 (+B) - 1A-4 | Always | Below 1 Ω |
| D34-2 (+B) - 1A-4 | Always | Below 1 Ω |
| 1A-2 - 1B-5 | Always | Below 1 Ω |
| 1A-3 - Body ground | Always | Below 1 Ω |
| D33-2 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| D34-2 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| 1A-2 or 1B-5 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 22.INSPECT NO. 1 INTEGRATION RELAY (A/F) |
Inspect the No. 1 integration relay (A/F) .
|
| ||||
| OK | ||
| ||