POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) > Driver Side Power Window does not Operate with Power Window Master Switch |

| 1.CHECK LIN COMMUNICATION SYSTEM |
Check for LIN communication system DTCs related to the power window control system (Click here).
|
| ||||
| OK | |
| 2.CHECK FOR DTC (B2312) |
Check if DTC B2312 is output (Click here).
|
| ||||
| OK | |
| 3.READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR) |
Use the Data List to check if the driver side motor is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door P/W Up SW | Driver side power window MANUAL UP switch signal / ON or OFF | ON: Driver side switch operated OFF: Driver side switch not operated | - |
| D Door P/W Down SW | Driver side power window MANUAL DOWN switch signal / ON or OFF | ON: Driver side switch operated OFF: Driver side switch not operated | - |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - BATTERY AND BODY GROUND) |
![]() |
Disconnect the N2 master switch connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N2-3 (B) - Body ground | Always | 11 to 14 V |
| N2-13 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| N2-1 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE MOTOR - BATTERY AND BODY GROUND) |
![]() |
Disconnect the N12 motor connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N12-2 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| N12-1 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR) |
![]() |
Disconnect the N2 master switch connector.
Disconnect the N12 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N2-4 (UP) - N12-10 (UP) | Always | Below 1 Ω |
| N2-5 (DOWN) - N12-7 (DOWN) | Always | Below 1 Ω |
| N2-4 (UP) - Body ground | Always | 10 kΩ or higher |
| N2-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Remove the driver side motor (Click here).
Apply positive (+) battery voltage to connector terminal 2 (B).
Apply negative (-) battery voltage to connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 (B) Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 10 (UP) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 10 (UP) | Motor gear rotates clockwise |
| Battery positive (+) → 2 (B) Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 7 (DOWN) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 7 (DOWN) | Motor gear rotates counterclockwise |
|
| ||||
| OK | ||
| ||